This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


WD headlight ground
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Lingle View Drop Down
Bronze Level
Bronze Level


Joined: 30 Sep 2022
Location: Iowa
Points: 23 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lingle Quote  Post ReplyReply Direct Link To This Post Topic: WD headlight ground
    Posted: 17 Jun 2024 at 1:11pm
anyone done something different with the ground for their headlights rather than the light frame tube to the tractor frame?  I am thinking of drilling out the rivet holding the headlight brass grounding strap and then re-rivet with a dedicated grounding wire?  maybe upgrade to LED headlight bucket?  FYI this would be used on both my WD and WD45.
35 and 41 WM crawlers, 49 WD, 53 WD45 wide front, 49 JD A, 52 JD B
Back to Top
Sponsored Links


Back to Top
Lingle View Drop Down
Bronze Level
Bronze Level


Joined: 30 Sep 2022
Location: Iowa
Points: 23 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lingle Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2024 at 1:14pm
so must not have searched very well and I just found this forum post: https://www.allischalmers.com/forum/wd45-headlights-not-working_topic169401.html looks like adding a separate ground to the reflector is the way to go.  anyone upgrade the socket to be a LED?
35 and 41 WM crawlers, 49 WD, 53 WD45 wide front, 49 JD A, 52 JD B
Back to Top
55allis View Drop Down
Orange Level
Orange Level
Avatar

Joined: 30 Jun 2020
Location: Griswold Iowa
Points: 710 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 55allis Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2024 at 1:44pm
I put a sealed beam in the original mounting but it was only a halogen bulb.
It was a 4.5” round so I’m sure there is a led version.
I found a 1/4” air hose that I put around the outside of the bulb and the inside of the original clamp and it would keep everything tight.
1955 AC WD45 diesel with D262 repower, 1949 AC WD45
Back to Top
Lingle View Drop Down
Bronze Level
Bronze Level


Joined: 30 Sep 2022
Location: Iowa
Points: 23 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lingle Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2024 at 2:39pm
Originally posted by 55allis 55allis wrote:

I put a sealed beam in the original mounting but it was only a halogen bulb.
It was a 4.5” round so I’m sure there is a led version.
I found a 1/4” air hose that I put around the outside of the bulb and the inside of the original clamp and it would keep everything tight.

Any chance you may have a PN?  also were you able to reuse the outer clamp and did you need the seal?
35 and 41 WM crawlers, 49 WD, 53 WD45 wide front, 49 JD A, 52 JD B
Back to Top
PaulB View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 4747 		Post Options Post Options   Thanks (0) Thanks(0)   Quote PaulB Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2024 at 6:56pm
I should be easy enough to run a second wire in the mount tube and have the extra ground completely hidden.
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
Back to Top
AC720Man View Drop Down
Orange Level
Orange Level
Avatar

Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 4926 		Post Options Post Options   Thanks (0) Thanks(0)   Quote AC720Man Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2024 at 10:15pm
I did what Paul suggested a few years ago on my WD. Grounding is so important on these ole tractors. It will drive you crazy sometimes. I ran a new ground from each light bucket to the frame of the light bar. All hidden in the light tube, cleaned the ground area that the battery grounds to(2nd time) upgraded to 2/0 welding cable and all my issues disappeared. Old metal rusts and the ground doesn't work well. 
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
Back to Top
55allis View Drop Down
Orange Level
Orange Level
Avatar

Joined: 30 Jun 2020
Location: Griswold Iowa
Points: 710 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 55allis Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2024 at 11:08pm
Originally posted by Lingle Lingle wrote:

Originally posted by 55allis 55allis wrote:

I put a sealed beam in the original mounting but it was only a halogen bulb.
It was a 4.5” round so I’m sure there is a led version.
I found a 1/4” air hose that I put around the outside of the bulb and the inside of the original clamp and it would keep everything tight.


Any chance you may have a PN?  also were you able to reuse the outer clamp and did you need the seal?

I use a par 36 sealed beam and yes I kept the original clamp.
I had a high/low beam light in it for awhile with 3 wires running through the original pipe but than just ran the two wires for ground and high beam.
I can try to get a closer picture tomorrow but this is all I have right now.
1955 AC WD45 diesel with D262 repower, 1949 AC WD45
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.094 seconds.


Help Support the
Unofficial Allis Forum