| Author |
 Topic Search  Topic Options
|
KChallener 
Bronze Level
Joined: 06 Dec 2023
Location: Meadville, PA
Points: 8
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: CA Crankshaft
Posted: 06 Dec 2023 at 1:04pm |
|
My newly acquired CA has a bent crankshaft. I have searched all the websites I can find to no avail. Anyone have a suggestion or know where I might find one?
Thanks,
Ken
|
 |
|
Sponsored Links
|
|
|
PaulB
Orange Level
Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 4722
|
Post Options
Thanks(0)
Quote Reply
Posted: 06 Dec 2023 at 3:06pm |
I have plenty of them, although I'm in Maryland very near Gettysburg, Pa. I'm sure if you call Branda at Sandy Lake Implement, they'll have something for you. 724-376-2489 Sandy Lake Implement is right in you area.
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
|
|
Mikez
Orange Level Access
Joined: 16 Jan 2013
Location: Usa
Points: 8379
|
Post Options
Thanks(0)
Quote Reply
Posted: 06 Dec 2023 at 5:13pm |
|
I sent you a private message
|
|
dfwallis
Orange Level
Joined: 09 Mar 2023
Location: DFW
Points: 627
|
Post Options
Thanks(0)
Quote Reply
Posted: 06 Dec 2023 at 7:25pm |
|
How does a crankshaft typically get bent?? They're pretty beefy.
|
|
Codger
Orange Level
Joined: 23 Dec 2020
Location: Illinois
Points: 2050
|
Post Options
Thanks(0)
Quote Reply
Posted: 06 Dec 2023 at 7:37pm |
|
The torsional "twist" imparted through them with clutch engagement having a heavy load to pull. When you set the shaft up on blocks and rotate it using an indicator on a round bearing surface this minor twist results in the shaft "heaving" which is interpreted as bending. They don't bend as such like folding apiece of metal over in a bench vise.
Edited by Codger - 06 Dec 2023 at 7:38pm
|
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
jdeere562
Bronze Level
Joined: 02 Oct 2023
Location: SW Iowa
Points: 31
|
Post Options
Thanks(0)
Quote Reply
Posted: 06 Dec 2023 at 11:24pm |
 dfwallis wrote:
How does a crankshaft typically get bent?? They're pretty beefy. |
I bent one once in a WC pulling tractor. But had beefed up the engine some. Put in a WD45 crank and rods for more stroke. Had some 4020 JD sleeves machined for the block and 454 big block Chevy pistons as I recall.
Also reworked and ported the cylinder head, intake and exhaust. Ran a D19 carb, had to drill jets to get it running properly. Always wanted to hide a nitrous bottle somewhere...LOL!
It would normally spit out the PTO gearbox on the dyno, before you could get a HP reading. Been a lot of years ago.
|
|
Lon(MN)
Orange Level
Joined: 11 Sep 2009
Location: Elk River,MN
Points: 1966
|
Post Options
Thanks(0)
Quote Reply
Posted: 07 Dec 2023 at 4:58am |
|
I have several, but a little ways away.
|
|
http://lonsallischalmers.com
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20479
|
Post Options
Thanks(1)
Quote Reply
Posted: 07 Dec 2023 at 5:23am |
|
I'm still trying to figure out how a "CA" engine would ever have enough BANG in the combustion chamber to bent a crankshaft ?? Must be a bearing burn out related failure ????
|
|
KChallener
Bronze Level
Joined: 06 Dec 2023
Location: Meadville, PA
Points: 8
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Dec 2023 at 4:55am |
|
Thanks for all the comments. I will call SLE (Sandy Lake). It looks like the A, C, and CA cranks were all the same? Pull the crank, mains, etc. Rod bearings were burn and scored. My guess is that there was a main failure at sometime, probably number one. Someone's been in there before, lots of Permatex. Before dissassebly I was getting about 45 psi compression on all 4 - any thoughts on that?
Ken
|
|
WF owner
Orange Level
Joined: 12 May 2013
Location: Bombay NY
Points: 4663
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Dec 2023 at 5:55am |
|
B, C and CA are all the same. A is an entirely different, and significantly bigger engine.
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20479
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Dec 2023 at 6:07am |
|
45 psi cranking with an electric starter spinning the engine ?? Pretty poor. Double that would be much better.
|
|
Les Kerf
Orange Level
Joined: 08 May 2020
Location: Idaho
Points: 777
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Dec 2023 at 7:26pm |
KChallener wrote:
... I was getting about 45 psi compression on all 4 - any thoughts on that?
Ken |
Better check cam timing, that's mighty even for being simply worn.
Edited by Les Kerf - 08 Dec 2023 at 7:29pm
|
|
KChallener
Bronze Level
Joined: 06 Dec 2023
Location: Meadville, PA
Points: 8
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Dec 2023 at 6:23am |
|
THanks. Will check pressures again after new pistons, sleeves, rings, crank and bearings.
Ken
|
|
