This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
ACC40 running rough |
Post Reply |
Author | |
Josh4God
Bronze Level Joined: 06 Dec 2023 Location: Modesto, CA Points: 11 |
Post Options
Thanks(0)
Posted: 06 Dec 2023 at 5:59pm |
I have an ACC-40 propane forklift that has been sitting in the corner of our hangar, not run for 3 years. Model # C 40 L PS Serial# AFR524866. I came on the job a year and a half ago, and recently decided to try and get it running. It is now fully functional, except for the alternator needing to be replaced.
The engine runs very rough and sounds like it is misfiring. I checked inside and there was alot of water in the engine oil. #1 piston actually has a puddle of oil on top of the head. I would look for engine manuals, but I do not know the engine make or model as the sticker on top of the heads that was probably the label is completely worn off. I have seen several users on the forum talk about having a continental f163 in the same model forklift, but several things look out of place. I will be sending some pictures. Any help finding out the make and model of this engine, and manuals for it would be appreciated.
|
|
Sponsored Links | |
Josh4God
Bronze Level Joined: 06 Dec 2023 Location: Modesto, CA Points: 11 |
Post Options
Thanks(0)
|
|
|
Josh4God
Bronze Level Joined: 06 Dec 2023 Location: Modesto, CA Points: 11 |
Post Options
Thanks(0)
|
|
|
Josh4God
Bronze Level Joined: 06 Dec 2023 Location: Modesto, CA Points: 11 |
Post Options
Thanks(0)
|
|
|
Josh4God
Bronze Level Joined: 06 Dec 2023 Location: Modesto, CA Points: 11 |
Post Options
Thanks(0)
|
|
|
steve(ill)
Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 81254 |
Post Options
Thanks(0)
|
another view
|
|
Like them all, but love the "B"s.
|
|
jaybmiller
Orange Level Access Joined: 12 Sep 2009 Location: Greensville,Ont Points: 22472 |
Post Options
Thanks(0)
|
first guess.... plugs not wired up right ? I got a deal on D-14 #3, ran rough...just got onto trailer. get home, rewire plugs from 1-2-3-4 to 1-2-4-3, ran like a top ! |
|
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor) Never burn your bridges, unless you can walk on water |
|
steve(ill)
Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 81254 |
Post Options
Thanks(0)
|
fork trucks normally came with a Continental f135 , f163 or buda 153 .... NONE of the valve covers looked like that..... Is it aluminum ? Looks more like a small car engine ??
I would look all over that motor and try to find some casting number, stamping, or something that might lead you in the right direction. The engine runs very rough and sounds like it is misfiring. I checked inside and there was alot of water in the engine oil. #1 piston actually has a puddle of oil on top of the head. You might have a blown head gasket / etc... As Jay said... you might take compression ... roll motor over slowly with plugs out and figure out which pistons come up on compression in what order. .......... cleaning the distributor and point is a good idea.
Edited by steve(ill) - 06 Dec 2023 at 6:40pm |
|
Like them all, but love the "B"s.
|
|
Josh4God
Bronze Level Joined: 06 Dec 2023 Location: Modesto, CA Points: 11 |
Post Options
Thanks(0)
|
Thank you both! I did not think about rewiring the plugs. I have already cleaned the distributor points but that was about a month ago when I started the project. I will check the firing order. Also, I found this FB27 number stamped onto the left side of the block. I included a picture of it.
|
|
Josh4God
Bronze Level Joined: 06 Dec 2023 Location: Modesto, CA Points: 11 |
Post Options
Thanks(0)
|
I checked the firing order by checking the order of compression strokes. They match the order in which the plugs are wired up. It is 1-3-4-2. It sounds more like it is the head gasket.
|
|
jaybmiller
Orange Level Access Joined: 12 Sep 2009 Location: Greensville,Ont Points: 22472 |
Post Options
Thanks(0)
|
curiously.. 1-3-4-2 is 1-2-4-3 if you go the other way.... please humour me and try it Jay
|
|
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor) Never burn your bridges, unless you can walk on water |
|
DiyDave
Orange Level Access Joined: 11 Sep 2009 Location: Gambrills, MD Points: 51703 |
Post Options
Thanks(0)
|
That motor looks like an import, to me. Its a very late model, with that paint and tin, and I am not familiar with late model stuff. Is the dealer that is on the sticker still in business? If so a call to them, or whoever bought them out, might be get you some info...
|
|
Source: Babylon Bee. Sponsored by BRAWNDO, its got what you need!
|
|
Josh4God
Bronze Level Joined: 06 Dec 2023 Location: Modesto, CA Points: 11 |
Post Options
Thanks(0)
|
Yes, the dealer sticker is still on the truck. I will give them a call to see if they know anything about the engine.
|
|
Josh4God
Bronze Level Joined: 06 Dec 2023 Location: Modesto, CA Points: 11 |
Post Options
Thanks(0)
|
I will give it a try.
|
|
Josh4God
Bronze Level Joined: 06 Dec 2023 Location: Modesto, CA Points: 11 |
Post Options
Thanks(0)
|
I tried wiring it 1-2-4-3 and it would not start. After re-wiring it to 1-3-4-2 the engine started successfully.
|
|
steve(ill)
Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 81254 |
Post Options
Thanks(0)
|
the majority of engines are 1-3-4-2 ............. Allis and a couple others were 1-2-4-3.
With that aluminum finned valve cover.. it sure look like a small automotive engine from 1980 . ??
|
|
Like them all, but love the "B"s.
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |