This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Thanks and another question
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
BillinAlberta View Drop Down
Silver Level
Silver Level
Avatar

Joined: 12 Sep 2009
Location: Saskatchewan
Points: 356 		Post Options Post Options   Thanks (0) Thanks(0)   Quote BillinAlberta Quote  Post ReplyReply Direct Link To This Post Topic: Thanks and another question
    Posted: 16 Jun 2023 at 11:13am
  Thanks to all the experienced folks posting about the 7000 series tractors.
I bought a 7020 and needed  to get it ready to go for haying and bush hogging
but the pto would not shut off.The hints I picked up on here plus using the 
service manual got me going.Many thanks!
   When using a 7 foot woods rotary mower will I damage the pto clutch
if I don't have an overrunning clutch? What type or brand of clutch do you recommend?
   After a couple of years with open station tractors I am loving the quiet cab 
and extra convienience of the power shift.
Back to Top
Sponsored Links


Back to Top
Ron(AB) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 27 Dec 2009
Location: Alberta
Points: 962 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Ron(AB) Quote  Post ReplyReply Direct Link To This Post Posted: 16 Jun 2023 at 12:53pm
a slip clutch and a shear pin.
405, 7000, 7050, 8050, 8070, L3, 2300 & 2600 disk
Back to Top
BillinAlberta View Drop Down
Silver Level
Silver Level
Avatar

Joined: 12 Sep 2009
Location: Saskatchewan
Points: 356 		Post Options Post Options   Thanks (0) Thanks(0)   Quote BillinAlberta Quote  Post ReplyReply Direct Link To This Post Posted: 16 Jun 2023 at 5:55pm
If there is a brake on the pto will it cause excess wear if it is constantly
stopping that much spinning mass?
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21833 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 16 Jun 2023 at 8:39pm
If you throw it in/out all the time, I suspect you sure wouldn't do the PTO brake any good. Best to have the engine at slow idle to shut down the PTO. OR, get an overrunning clutch on the mower.
Back to Top
BillinAlberta View Drop Down
Silver Level
Silver Level
Avatar

Joined: 12 Sep 2009
Location: Saskatchewan
Points: 356 		Post Options Post Options   Thanks (0) Thanks(0)   Quote BillinAlberta Quote  Post ReplyReply Direct Link To This Post Posted: 16 Jun 2023 at 10:34pm
I am looking for a clutch. A&I have 1 rated at 75 hp.Hopefully
that is stout enough.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.066 seconds.


Help Support the
Unofficial Allis Forum