| Author |
 Topic Search  Topic Options
|
Svnty7 
Bronze Level
Joined: 28 May 2022
Location: Indiana
Points: 16
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Xt 190 hydraulic pressure
Posted: 28 May 2022 at 9:35pm |
|
Greetings,
I have a XT 190 with a hydraulic issue.
800 to 900 psi on the raise function on the remotes, 2300 psi on the lower
Tractor won’t pick heavy implements
When hookup up the right way. When I switch hoses to the down coupling it will pick up anything? I can’t see how it would be the pump since I have good pressure on one side???????? I did change the relief valve with new one. No change?
|
 |
|
Sponsored Links
|
|
|
MACK
Orange Level
Joined: 17 Nov 2009
Points: 7664
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 May 2022 at 10:06pm |
|
You have a bad coupler. MACK
|
|
Svnty7
Bronze Level
Joined: 28 May 2022
Location: Indiana
Points: 16
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 May 2022 at 11:29am |
|
Thank you I’ll give that a try
|
|
Svnty7
Bronze Level
Joined: 28 May 2022
Location: Indiana
Points: 16
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 May 2022 at 11:31am |
|
Actually it does the same thing on both sets of remotes. Two bad couplers??
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8163
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 May 2022 at 1:06pm |
|
Well...that 2300lb pressure is in the valve stack soooo....changing couplers is cheap and easy...new never hurts anyway.
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20191
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 May 2022 at 6:34pm |
|
Replace both hose ends with correct tips on the cylinder that is bothering.
|
|
AC720Man
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 4855
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 May 2022 at 7:50pm |
|
If your using couplers that are a ball inside, make sure the hose end is the same way. I was never able to get a pointed fitting to work in a ball style coupling or vise versa.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
Svnty7
Bronze Level
Joined: 28 May 2022
Location: Indiana
Points: 16
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 May 2022 at 8:25pm |
|
Tried new couplings on both sides. Still low pressure on the “raise” coupling. Normal pressure on the low side. It does the same thing on my haybine disc and c mulcher
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20191
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 May 2022 at 9:09pm |
|
Now, two new couplers to match the hose tips. EDIT: Just so you aren't wasting our time, when a coupler locks up and movement of the hyd cylinder stops, the engine will labor as the hydraulic pump makes 2300 psi against the relief valve. If the engine doesn't labor when movement stops, you have a bad relief valve, pump issues or low on hyd oil !!! HYD HOSES ARE CONNECTED IN PAIRS TO THE RIGHT OF CENTER OR LEFT OF CENTER ON THE TRACTOR, NOT ONE ON EACH SIDE.
Edited by DrAllis - 30 May 2022 at 6:22am
|
|
MACK
Orange Level
Joined: 17 Nov 2009
Points: 7664
|
Post Options
Thanks(0)
Quote Reply
Posted: 30 May 2022 at 7:29am |
|
With engine off, will both levers stay in detent? MACK
|
|
Svnty7
Bronze Level
Joined: 28 May 2022
Location: Indiana
Points: 16
|
Post Options
Thanks(0)
Quote Reply
Posted: 31 May 2022 at 8:27pm |
|
Haven’t had a chance to see how much the engine labors when it completes cycle. They do stay in detent when the motor is of. I’m clear on how to hook up hoses……. Thanks for all your help . Just in case I’m going to buy a complete new set of male and female couplers and try that again
|
|
