This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Construction and other equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


ISOTrack pin tool
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
yzfarmgirl28 View Drop Down
Silver Level
Silver Level
Avatar

Joined: 15 Feb 2012
Location: wisconsin
Points: 249 		Post Options Post Options   Thanks (0) Thanks(0)   Quote yzfarmgirl28 Quote  Post ReplyReply Direct Link To This Post Topic: ISOTrack pin tool
    Posted: 15 Apr 2022 at 1:53pm
Looking for anyone that is knowledgeable about track pin removal. Need to remove/shorten a H3 track. Any information or expertise advise appreciated.
Would purchase or rent any type of pin press available.
Thanks
Back to Top
Sponsored Links


Back to Top
DiyDave View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: Gambrills, MD
Points: 51737 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DiyDave Quote  Post ReplyReply Direct Link To This Post Posted: 15 Apr 2022 at 6:16pm
If you are shortening a track, then the UC is already fubar, and now you are gonna tear up the sprockets, too!  JMHO.  Someone should be along to talk about the tool...Wink
Source: Babylon Bee. Sponsored by BRAWNDO, its got what you need!
Back to Top
steve(ill) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: illinois
Points: 81380 		Post Options Post Options   Thanks (0) Thanks(0)   Quote steve(ill) Quote  Post ReplyReply Direct Link To This Post Posted: 15 Apr 2022 at 7:03pm
YEP... chain is stretched so it does not fit the sprocket... Removing a link does not fix the problem... might make it worse with a snug chain.
Like them all, but love the "B"s.
Back to Top
Coke-in-MN View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Afton MN
Points: 41609 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Coke-in-MN Quote  Post ReplyReply Direct Link To This Post Posted: 15 Apr 2022 at 10:40pm
Master pin can be driven out with a BFH by using a pin held against the master link . 
Next problem is if you need to remove one link of which end do you remove - as you will need to remove another link . 
  That link removal will change the overall dimension of the track and the on-center measurement between links - WHICH MEANS - the SPROCKET PITCH to BUSHING On-center will be off and lead to wear on both sprocket and track . 
  Check the track to see if it has been turned in past - if not then have it pressed and turned at a track shop - to bring it back to close to acceptable specifications .
  OR CUT OUT 1 Link and ruin the ability to turn it later along with putting stress or rear case and bearings and damaging them beyond salvage later   
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.047 seconds.


Help Support the
Unofficial Allis Forum