| Author |
 Topic Search  Topic Options
|
1947WC 
Silver Level
Joined: 11 Dec 2015
Location: Wisconsin
Points: 214
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Battery cables
Posted: 08 Aug 2021 at 2:37pm |
Does any one know if 8guage cables are heavy enough on a 12 volt conversion.
|
 |
|
Sponsored Links
|
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 87040
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Aug 2021 at 3:16pm |
|
NO... not for the starter... You need at least 4 gauge...2 would be advised.. smaller numbers are BETTER.
|
|
Like them all, but love the "B"s.
|
|
Dakota Dave
Orange Level
Joined: 12 Sep 2009
Location: ND
Points: 3969
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Aug 2021 at 3:23pm |
|
No at least 4 only if it's short.2 would be better O if it's a long run.i get mine made at the local JD they make to the exact length and hyd pressed ends.
Edited by Dakota Dave - 08 Aug 2021 at 3:25pm
|
|
DSeries4
Orange Level
Joined: 12 Sep 2009
Location: Ontario, Canada
Points: 7479
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Aug 2021 at 8:50pm |
|
I always go for thicker cables than what is called for. Might be overkill, but I know they shouldn't cause any problems for a long time. I just replaced the original 4 gauge cables with 0 gauge on my 1960 D14.
|
|
'49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '61 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080
|
|
Clay
Orange Level
Joined: 11 Sep 2009
Location: Udall, Kansas
Points: 9782
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Aug 2021 at 12:19pm |
I make most of my replacement battery cables. NAPA has terminals which can be soldered. Welding cable works great. Remove only enough insulation to reach bottom of the conductor hole in the terminal. Tin the bare cable. Insert cable into the conductor hole in the terminal. Coat the bare wire with solder paste. Heat the cable with a HOT soldering copper and add melted rosin core solder . Allow to cool before moving the wire.
|
|
ac hunter
Orange Level
Joined: 05 Jan 2011
Location: OHIO
Points: 1045
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Aug 2021 at 2:38pm |
|
I like to put a piece of shrink tube over the end of the cable covering as much of the clamp as possible. Got some heavy shrink tube from NAPA some years ago that has some sort of sealer that melts and seals the ends really well. Amen about the heavy cable.
|
|
1947WC
Silver Level
Joined: 11 Dec 2015
Location: Wisconsin
Points: 214
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Aug 2021 at 5:09pm |
Thanks to all who helped me on the battery cables.
|
|
Steve in NJ
Orange Level Access
Joined: 12 Sep 2009
Location: Andover, NJ
Points: 11978
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Aug 2021 at 7:03am |
We have Battery cables in stock. I also make cables to the customer's C to C measurements. As the guys mentioned, 4 ga. is the norm for 12V systems. Using a 1 gauge cable (the norm for 6v) would be plenty heavy enough on a 12V system.... Steve@B&B
|
|
39'RC, 43'WC, 48'B, 49'G, 50'WF, 65 Big 10, 67'B-110, 75'716H, 2-620's, & a Motorhead wife
|
|
