This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Construction and other equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


7G-B belly pan
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
fbbeale View Drop Down
Bronze Level
Bronze Level


Joined: 28 Feb 2020
Location: Bowling Green V
Points: 14 		Post Options Post Options   Thanks (0) Thanks(0)   Quote fbbeale Quote  Post ReplyReply Direct Link To This Post Topic: 7G-B belly pan
    Posted: 19 May 2021 at 8:20pm
The engine belly pan was missing from my 7G-B when I purchased it.  I am starting to do some clearing where it may become an issue.  Just curious if anyone knows approximately how thick the metal is that the original is made from.  I think I have enough scrap metal to make one but don't want to build any thicker than necessary or too thin.  Thanks!
Back to Top
Sponsored Links


Back to Top
gemdozer View Drop Down
Orange Level
Orange Level


Joined: 17 Sep 2009
Points: 989 		Post Options Post Options   Thanks (0) Thanks(0)   Quote gemdozer Quote  Post ReplyReply Direct Link To This Post Posted: 19 May 2021 at 9:26pm
The belly pan metal should be 7/16 or 1/2 and you could check the transmission and torque need to be protect
Back to Top
fbbeale View Drop Down
Bronze Level
Bronze Level


Joined: 28 Feb 2020
Location: Bowling Green V
Points: 14 		Post Options Post Options   Thanks (0) Thanks(0)   Quote fbbeale Quote  Post ReplyReply Direct Link To This Post Posted: 19 May 2021 at 10:22pm
Thanks! Fortunately I have the transmission belly pan.
Back to Top
DMiller View Drop Down
Orange Level Access
Orange Level Access


Joined: 14 Sep 2009
Location: Hermann, Mo
Points: 31151 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DMiller Quote  Post ReplyReply Direct Link To This Post Posted: 20 May 2021 at 4:49am
This was the 7G unit I had repaired, was 1/4" thick and appeared as OE.






Edited by DMiller - 20 May 2021 at 4:50am
Back to Top
7G-B owner View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 17 Jun 2021
Location: Virginia
Points: 3 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 7G-B owner Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2021 at 12:37pm
I just pulled the transmission belly pan on mine and it was 1/4 inch.  I'm not sure of engine belly pan yet.  

Anyone have any ideas on steering and transmission shifting issues?  Transmission pressure dropping, and the filters and screens appear good.  I only pulled the screen at the very bottom of the transmission, but it was super clean.  Steering filter was clean.  Is it a pump issue? Final Drive?  The final drive going out wouldn't cause my transmission pressure to drop sporadically would it?  That doesn't make sense to me.

Any help would be greatly appreciated.
Back to Top
DMiller View Drop Down
Orange Level Access
Orange Level Access


Joined: 14 Sep 2009
Location: Hermann, Mo
Points: 31151 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DMiller Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2021 at 12:43pm
G-B was a little different than the 7G but trans was the same. According to information I dug thru the peddle steer clutch actuation could be problematic at times but the main issue on the 7G was seal failures internal to clutch packs.
I dealt with that on my 7G when had it. Are not much available for these where I ended up working thru a hydraulics shop to make different styles work. The trans shift seals at the ends of the clutch pack shafts were the hardest to come up with and worst leakers.
Back to Top
gemdozer View Drop Down
Orange Level
Orange Level


Joined: 17 Sep 2009
Points: 989 		Post Options Post Options   Thanks (0) Thanks(0)   Quote gemdozer Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jun 2021 at 5:09pm
Did you removed the front transmission streaner it is the first one to check.
Back to Top
HD6GTOM View Drop Down
Orange Level
Orange Level
Avatar

Joined: 30 Nov 2009
Location: MADISON CO IA
Points: 6627 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HD6GTOM Quote  Post ReplyReply Direct Link To This Post Posted: 19 Jun 2021 at 10:44pm
The bolts holding the pans on the 6g's are fine threaded. I don't know if the 7's are the same.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum