| Author |
 Topic Search  Topic Options
|
AC720Man 
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 4926
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: 720 Hydro oil
Posted: 14 Sep 2020 at 8:14pm |
|
Been a few years since I changed my hydro oil(less than a 100 hrs ago). So I decided to change the oil and filter since this one sets outside under cover. Drained the fluid over night, picked up 6 quarts and filter. After 5 quarts I checked the level and it was way above the full mark. I started it, ran it around a little bit, let it set for 15 minutes and rechecked the level again. It is still above the mark. What am I missing here? Hood clearly says 6 quarts. No way the lines to the front and oil cooler could have more than a quart in them? Wouldn’t that have drained out?
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
 |
|
Sponsored Links
|
|
|
Brad in WA
Bronze Level Access
Joined: 29 Sep 2009
Location: Lynden,WA
Points: 194
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 Sep 2020 at 4:29am |
|
Did you take both plugs out when you drained it? I think the temp sensor has to be removed to get all the oil out.
|
|
AC720Man
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 4926
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 Sep 2020 at 10:15am |
|
I removed the the temp sensor to drain as it is the lowest point. Guess I need to pull my book out.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
Steve in NJ
Orange Level Access
Joined: 12 Sep 2009
Location: Andover, NJ
Points: 11818
|
Post Options
Thanks(0)
Quote Reply
Posted: 16 Sep 2020 at 8:20am |
Rob, I think both plugs need to be out to drain the tranny completely. Don't remember myself now. Sheesh! A mind is a terrible thing to waste... LOL! Steve@B&B
|
|
39'RC, 43'WC, 48'B, 49'G, 50'WF, 65 Big 10, 67'B-110, 75'716H, 2-620's, & a Motorhead wife
|
|
Bird76Mojo
Silver Level
Joined: 12 Mar 2015
Location: Illinois
Points: 221
|
Post Options
Thanks(0)
Quote Reply
Posted: 20 Sep 2020 at 1:57am |
|
I took out the sending unit today, let it drain for quite a while, then removed the suction tube and a BUNCH more fluid came out. I'd say removing both is the best route to take..
I guarantee that there's a quart in the hydro lines, cooler, pump, front circuit, rear circuit, etc..
|
|
AC720Man
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 4926
|
Post Options
Thanks(0)
Quote Reply
Posted: 20 Sep 2020 at 7:39pm |
|
Thanks Mojo, I do now remember doing that the last time. There is a procedure in the book describing how to bleed the system afterwards. I think I stuck a female fitting upfront and shot it in a 5 gallon bucket. It will make a mess even though it does take much to clear the air. A lot of pressure there.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
Bird76Mojo
Silver Level
Joined: 12 Mar 2015
Location: Illinois
Points: 221
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Sep 2020 at 7:25pm |
|
It should flow around 2.5 gallons per minute at 500psi.
Not enough flow to run a hydraulic chainsaw unfortunately..
|
|
