This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


7020 transmission brake
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Blustery Knoll Farm View Drop Down
Bronze Level
Bronze Level


Joined: 04 Dec 2017
Location: Northern IL
Points: 117 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Blustery Knoll Farm Quote  Post ReplyReply Direct Link To This Post Topic: 7020 transmission brake
    Posted: 30 May 2019 at 10:26pm
My 7020 grinds going into gear cold. What is the appropriate way to adjust the transmission brake?

I have loosened the clamp on the clutch cable and pulled out all the slack and it still grinds. Am I not adjusting it properly, or is the trans brake bad?
Back to Top
Sponsored Links


Back to Top
SteveM C/IL View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8547 		Post Options Post Options   Thanks (0) Thanks(0)   Quote SteveM C/IL Quote  Post ReplyReply Direct Link To This Post Posted: 30 May 2019 at 10:38pm
My 8070 has always tried to grind cold. I just wait a little longer to try and shift it. I think it might be normal. Warmed a little and it's fine.
Back to Top
Blustery Knoll Farm View Drop Down
Bronze Level
Bronze Level


Joined: 04 Dec 2017
Location: Northern IL
Points: 117 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Blustery Knoll Farm Quote  Post ReplyReply Direct Link To This Post Posted: 30 May 2019 at 10:59pm
I'd think it was normal, except my 7040 will stop the tractor if it is in gear and I push the clutch pedal to the floor. It never grinds, as long as I push the pedal to the floor.
Back to Top
Moneypit View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 13 Sep 2018
Location: Barnesville mn
Points: 81 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Moneypit Quote  Post ReplyReply Direct Link To This Post Posted: 31 May 2019 at 1:37am
Replace the ends on the cable and maybe the cable. If there is to much wear in the ends it'll grind
Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664 		Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 31 May 2019 at 6:51am
Replace pivot bushing and pin. Make sure there is not a thick rug under clutch pedal.        MACK
Back to Top
Lonn View Drop Down
Orange Level
Orange Level
Avatar

Joined: 16 Sep 2009
Location: Назарово,Russia
Points: 29792 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lonn Quote  Post ReplyReply Direct Link To This Post Posted: 31 May 2019 at 7:07am
On my brother's 7030 the pin and bushings didn't look bad but after I replaced them the problem was solved. That's where I'd look next.
-- --- .... .- -- -- .- -.. / .-- .- ... / .- / -- ..- .-. -.. . .-. .. -. --. / -.-. .... .. .-.. -.. / .-. .- .--. .. ... -
Wink
I am a Russian Bot
Back to Top
Blustery Knoll Farm View Drop Down
Bronze Level
Bronze Level


Joined: 04 Dec 2017
Location: Northern IL
Points: 117 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Blustery Knoll Farm Quote  Post ReplyReply Direct Link To This Post Posted: 31 May 2019 at 8:01am
How far is the spool supposed to come out of the valve body when fully depressed? Pivot bushing is tight.

There's no rug in the cab, so that's not the problem.

Edited by Blustery Knoll Farm - 31 May 2019 at 8:02am
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21567 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 31 May 2019 at 8:19am
Whenever I repaired a trans brake complaint, it was ALWAYS replace the two fork pivot bushings and the ball joint on the end of the cable, spray WD40 all over everything and adjust the cable to proper length (pull hard forward on the cable and tighten the U-bolt). If you still have trouble after doing all that, there is potentially a warped clutch disc/plate or tranny brake issue.
Back to Top
Blustery Knoll Farm View Drop Down
Bronze Level
Bronze Level


Joined: 04 Dec 2017
Location: Northern IL
Points: 117 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Blustery Knoll Farm Quote  Post ReplyReply Direct Link To This Post Posted: 31 May 2019 at 9:27am
Previous owner said that he replaced the bushings a bit over a year ago. They feel tight.
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21567 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 31 May 2019 at 10:00am
Adjust the cable 1/8" TIGHTER yet. May have to use a prybar of some sort. Oil everything.
Back to Top
Blustery Knoll Farm View Drop Down
Bronze Level
Bronze Level


Joined: 04 Dec 2017
Location: Northern IL
Points: 117 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Blustery Knoll Farm Quote  Post ReplyReply Direct Link To This Post Posted: 31 May 2019 at 10:51am
I adjusted it 1/8" shorter so that the fork was actually moving the plate on the spool a bit and there's no change.
Back to Top
Lonn View Drop Down
Orange Level
Orange Level
Avatar

Joined: 16 Sep 2009
Location: Назарово,Russia
Points: 29792 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lonn Quote  Post ReplyReply Direct Link To This Post Posted: 31 May 2019 at 2:39pm
warped plates IMO
-- --- .... .- -- -- .- -.. / .-- .- ... / .- / -- ..- .-. -.. . .-. .. -. --. / -.-. .... .. .-.. -.. / .-. .- .--. .. ... -
Wink
I am a Russian Bot
Back to Top
Blustery Knoll Farm View Drop Down
Bronze Level
Bronze Level


Joined: 04 Dec 2017
Location: Northern IL
Points: 117 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Blustery Knoll Farm Quote  Post ReplyReply Direct Link To This Post Posted: 31 May 2019 at 8:34pm
I guess I'll live with it for a while then. Just wanted to rule out adjustment as the culprit first. It works fine once it is warmed up.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum