| Author |
 Topic Search  Topic Options
|
Allisplumber 
Bronze Level
Joined: 04 Jan 2016
Location: Wisconsin
Points: 76
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: D21 flywheel
Posted: 26 Nov 2018 at 10:34am |
|
I’m looking for a new or very good used D21 flywheel, thanks for any help
|
 |
|
Sponsored Links
|
|
|
NEVER green
Orange Level Access
Joined: 28 Feb 2013
Location: MN.
Points: 7528
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Nov 2018 at 4:17pm |
|
Steel??
|
|
2-8050 1-7080 6080 D-19 modelE & A 7040 R50
|
|
Allisplumber
Bronze Level
Joined: 04 Jan 2016
Location: Wisconsin
Points: 76
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Nov 2018 at 5:07pm |
|
Will be pulling farm stock class , but will be around 350 hp , 3000 rpms max , I know most all the guys I pull with still have the stock cast ones , steel would probably be the best way to go ?
|
|
ACFarmer
Orange Level Access
Joined: 13 Sep 2009
Location: Ohio
Points: 743
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Nov 2018 at 6:46pm |
|
If your taking the time to put one in, put in a steel flywheel. Even at 3000 and below.
|
|
Making A living everyday farming with and working on Allis Equipment
|
|
NEVER green
Orange Level Access
Joined: 28 Feb 2013
Location: MN.
Points: 7528
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Nov 2018 at 7:00pm |
|
You will sleep better at night with steel, wouldn t want to be libel for an injury or worse. I have a Rursch flywheel and 3 dick clutch, comes with rear engine plate slightly modified for low clearance bolts. Its for a 210, shaft same as a 21???
|
|
2-8050 1-7080 6080 D-19 modelE & A 7040 R50
|
|
Allisplumber
Bronze Level
Joined: 04 Jan 2016
Location: Wisconsin
Points: 76
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Nov 2018 at 7:35pm |
|
Not sure if the shaft is the same but the d21 takes the same clutch as a 210 and 220 so I would think so , how much you asking for the one you have ? Thanks
|
|
NEVER green
Orange Level Access
Joined: 28 Feb 2013
Location: MN.
Points: 7528
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Nov 2018 at 4:57pm |
|
How close are you to the twin cities? Im 40 miles west.
|
|
2-8050 1-7080 6080 D-19 modelE & A 7040 R50
|
|
Allisplumber
Bronze Level
Joined: 04 Jan 2016
Location: Wisconsin
Points: 76
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Nov 2018 at 7:28pm |
|
I’m east of Green Bay Wi , so your probably over 4 hours drive from me
|
|
NEVER green
Orange Level Access
Joined: 28 Feb 2013
Location: MN.
Points: 7528
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Nov 2018 at 4:17pm |
|
Isshh ......... Just talked to Darrin and a new billet steel 12.5 crowler triple disc is 49, so 2500 sounds reasonable, at least I try to be reasonable. Just measured the shaft size it is 1 3/8.
Let me know watchya think, there is others interested.
Edited by NEVER green - 29 Nov 2018 at 4:20pm
|
|
2-8050 1-7080 6080 D-19 modelE & A 7040 R50
|
|
injpumpEd
Orange Level Access
Joined: 13 Sep 2009
Location: Walnut IL
Points: 4921
|
Post Options
Thanks(0)
Quote Reply
Posted: 30 Nov 2018 at 8:24am |
|
D21/210/220 can all use the same clutch when it comes to replacements. I think the D21 has more room in bell housing with the top mounted release fork though, when considering dual, or triple disc setups. I run a dual disc, and the casting bump where the release shaft passes through required some grinding.
|
|
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!
|
|
