This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Distributor housing oil tube
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Bee View Drop Down
Orange Level
Orange Level


Joined: 14 Jun 2010
Location: NC
Points: 201 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Bee Quote  Post ReplyReply Direct Link To This Post Topic: Distributor housing oil tube
    Posted: 23 Jul 2010 at 2:13pm
Looking at other "B's" and the It manual I believe I am missing an oil tube which should run from the governor housing to the Distributor housing.  (1949B).  Anyone know if this is the case?  If so, where on the dist housing does the line attach? Thanks!!!
  
Bob, North Carolina

1949 B
Back to Top
Sponsored Links


Back to Top
GlenninPA View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Ashley, PA
Points: 5054 		Post Options Post Options   Thanks (0) Thanks(0)   Quote GlenninPA Quote  Post ReplyReply Direct Link To This Post Posted: 23 Jul 2010 at 2:24pm
in 1953, they put the Tee fitting on the oil line to the governor. I do not have a B that new, so I am at a loss to tell you where it hooks up. Before 1953, the oil line only went straight into the governor.
Back to Top
Lance/SC View Drop Down
Orange Level
Orange Level


Joined: 14 Sep 2009
Location: Lexington, SC
Points: 411 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lance/SC Quote  Post ReplyReply Direct Link To This Post Posted: 23 Jul 2010 at 3:35pm
Bee, on my '48 B the oil line runs from a fitting at the back of the block near the oil filter directly to the governor housing as in the front part of your B.  Where does that line go on your B?
Back to Top
Bee View Drop Down
Orange Level
Orange Level


Joined: 14 Jun 2010
Location: NC
Points: 201 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Bee Quote  Post ReplyReply Direct Link To This Post Posted: 23 Jul 2010 at 4:01pm
My line runs from the oil pump to the governor.  There is also a hole from the governor section to the distributor section.  From what I have read this hole is described as a "drain" hole which led me to believe I should have a feed line off a tee as Glen described.  Must be the design was changed after my 1949 was built.
Bob, North Carolina

1949 B
Back to Top
Steve in NJ View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Andover, NJ
Points: 11754 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Steve in NJ Quote  Post ReplyReply Direct Link To This Post Posted: 25 Jul 2010 at 3:29pm
My 48'B had the oil line coming off the Tee block in the cylinder head, down the side of the valve cover to where the  Govenor bellcrank pivots for the throttle linkage. I offer a new kit for that oil line if interested with the fittings.......
Steve@B&B  
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.078 seconds.


Help Support the
Unofficial Allis Forum