This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


wd hydralic pressure low
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3914 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Topic: wd hydralic pressure low
    Posted: 01 May 2017 at 9:51am
hyd . pressure was only getting around 1500 psi last summer raking hay  i have not looked in my service manual  yet or got on the parts look up .   what do i  need to repair ?       i have a gauge mounted on the port were the traction booster line gauge would go was watching it when i was haveing a hard time opening the 14 wheel hay rake  .   not running out of oil  just low pressure 
Back to Top
Sponsored Links


Back to Top
Allis dave View Drop Down
Orange Level
Orange Level


Joined: 10 May 2012
Location: Northern IN
Points: 3054 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Allis dave Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2017 at 10:12am
You'll get a better pressure reading if you hook a gauge up to the remote.

If that's your actual pressure, you'll have to pull the pump off and reseal it at minimum. Could be that some check valve spring springs are broken. I had a bout 700PSI from my pump. pulled it and 2 spring were broke. If after all that you still have low pressure, you can start adding shims to the unload valve in the pump.
Back to Top
Butch(OH) View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Lucerne Ohio
Points: 3842 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Butch(OH) Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2017 at 10:16am
AGCO used to sell a couple kits that between them had the bulk of the wearing parts, seals and gaskets included. Once rebuilt you reinstall the pump and check the pressure and then remove it again to shim the relief valve. Been many years since I have seen one that came close to spec for pressure, they all need more shims.
Back to Top
Ted J View Drop Down
Orange Level
Orange Level
Avatar

Joined: 05 Jul 2010
Location: La Crosse, WI
Points: 18943 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Ted J Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2017 at 10:20am
WHAT tractor is this on?
"Allis-Express"
19?? WC / 1941 C / 1952 CA / 1956 WD45 / 1957 WD45 / 1958 D-17
Back to Top
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3914 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2017 at 5:47pm
52 wd.        what kit Numbers should i be looking at? i do have a pump off of a 49wd on the shelf but i never seen it run
Back to Top
Butch(OH) View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Lucerne Ohio
Points: 3842 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Butch(OH) Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 2017 at 7:33pm
Go to AGCO parts books and they are listed at the bottom if the hydraulic pump section.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.094 seconds.


Help Support the
Unofficial Allis Forum