This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
h3 gas engine? |
Post Reply |
Author | |
troy31
Bronze Level Joined: 04 Feb 2017 Location: ky Points: 16 |
Post Options
Thanks(0)
Posted: 05 Feb 2017 at 8:32pm |
Anyone know we're to get a rebuild kit for a h3 gas crawler for a.good.price or were to get a complete motor to go in a h3 used or new.that's in good shape.. iv heard they have same.motor.as a d15 farm tractor but is it.a 149 or a 160 in the crawler
|
|
Sponsored Links | |
DSeries4
Orange Level Joined: 12 Sep 2009 Location: Ontario, Canada Points: 7306 |
Post Options
Thanks(0)
|
Both were used. Early models had the 149, later models had the 160. If it has an oil bath air cleaner, chances are it's a 149. The model and serial number is stamped on a flat surface close to the exhaust manifold near the back of the engine.
|
|
'49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '61 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080
|
|
Eric B
Orange Level Joined: 09 Feb 2012 Location: British Columbi Points: 922 |
Post Options
Thanks(0)
|
Overhaul kits are easy to get from dealers on this site and elsewhere too.
|
|
Currently- WD,WC,3WF's,2 D14's B. Previously- I 600,TL745,200,FL9,FR12,H3,816 LBH. Earth has no sorrow that Heaven cannot heal!
|
|
Tracy Martin TN
Orange Level Access Joined: 11 Sep 2009 Location: Gallatin,TN Points: 10608 |
Post Options
Thanks(0)
|
If it is a 160 cid, hold on to your wallet! HTH Tracy
|
|
No greater gift than healthy grandkids!
|
|
troy31
Bronze Level Joined: 04 Feb 2017 Location: ky Points: 16 |
Post Options
Thanks(0)
|
My only numbers on the block is 3-2987-r. Least it looks like a 3 at the beganing
|
|
nevans
Orange Level Joined: 06 Dec 2011 Location: Red Bud. IL Points: 837 |
Post Options
Thanks(0)
|
we have one that was overhauled nephew was going to put it in a b for pulling its a 160 will take 1750 Niel
|
|
Eric B
Orange Level Joined: 09 Feb 2012 Location: British Columbi Points: 922 |
Post Options
Thanks(0)
|
I'm not disputing your findings but sometimes you have to wire brush and/or use a sandpaper in order to get all the digits showing...
|
|
Currently- WD,WC,3WF's,2 D14's B. Previously- I 600,TL745,200,FL9,FR12,H3,816 LBH. Earth has no sorrow that Heaven cannot heal!
|
|
troy31
Bronze Level Joined: 04 Feb 2017 Location: ky Points: 16 |
Post Options
Thanks(0)
|
I cleaned it off good and that's the numbers...also noticed there is no fuel pump or place.for.one..so this is a.tractor motor, but can someone tell me what kind so I can get a rebuild kit
|
|
Eric B
Orange Level Joined: 09 Feb 2012 Location: British Columbi Points: 922 |
Post Options
Thanks(0)
|
If those are all the digits you have, you will likely have to pull the head to get the cubic inch or else ordering parts would be a leap in the dark. I have two D14's with the same looking block as you have and the row of digits start with "149" and a group of five numbers plus R at the end which has to do with compression ratio apparently. It's maybe more likely that you have a 149, however, you're really lucky if you have a 160...more sought after but way more for parts cost. |
|
Currently- WD,WC,3WF's,2 D14's B. Previously- I 600,TL745,200,FL9,FR12,H3,816 LBH. Earth has no sorrow that Heaven cannot heal!
|
|
JoeO(CMO)
Orange Level Joined: 11 Sep 2009 Location: Cent Missouri Points: 2694 |
Post Options
Thanks(0)
|
Probably 3 since it is a H3 with the serial. Could be looking at a 5 possibly which could have a 1 in front of it. Edited by JoeO(CMO) - 10 Feb 2017 at 9:44am |
|
|
|
Calvin Schmidt
Orange Level Joined: 11 Sep 2009 Location: Ontario Can. Points: 4520 |
Post Options
Thanks(0)
|
I checked the dealers parts book and H-3's serial # 6959 and lower had the 149 engine.
Serial 6959 and higher had the 160 engine. Serial number on the left side of the torque tube where the engine bolts to the torque tube.
|
|
Nothing is impossible if it is properly financed
|
|
troy31
Bronze Level Joined: 04 Feb 2017 Location: ky Points: 16 |
Post Options
Thanks(0)
|
This number is right on the block, same side as carb, toward the back...I'd show a photo but it won't let me upload from my phone, the engine ain't orginal cuz it does not have a fuel pump
|
|
Kipn
Orange Level Joined: 12 Sep 2009 Location: Tewksbury, Ma Points: 800 |
Post Options
Thanks(0)
|
Due to serial number, its a 149. It probabaly has an H in front of the 3, if it came out of a dozer.
|
|
1961 H3
|
|
pinball
Orange Level Access Joined: 28 May 2014 Location: missouriu Points: 6079 |
Post Options
Thanks(0)
|
Are you sure there is not a fuel pump. Never seen a gas motor with out one originally. Could it be the fuel pump went bad and removed and a plate put over it and they just used the pressure from the fuel tank. Just curious I guess. norm
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |