This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Construction and other equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Hd5g parts
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
DavidnTenIll View Drop Down
Bronze Level Access
Bronze Level Access
Avatar

Joined: 02 Nov 2014
Location: illinois
Points: 65 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DavidnTenIll Quote  Post ReplyReply Direct Link To This Post Topic: Hd5g parts
    Posted: 23 Jul 2016 at 8:31am
Looking for hd5g engine clutch shaft and front yoke with good tight splines.
Back to Top
Sponsored Links


Back to Top
Dozer View Drop Down
Orange Level
Orange Level


Joined: 16 Aug 2011
Location: SW New York
Points: 689 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Dozer Quote  Post ReplyReply Direct Link To This Post Posted: 23 Jul 2016 at 4:26pm
General Gear   Please post if you find a new yoke.
Back to Top
Coke-in-MN View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Afton MN
Points: 42033 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Coke-in-MN Quote  Post ReplyReply Direct Link To This Post Posted: 23 Jul 2016 at 6:59pm
that front yoke might be a problem as I found 1 out of about 8 I checked -
Clutch shaft - around but also hard to find a good one with no wear - couple I had were worn at pilot bearing end as well as splines .
 check that brass bushing in the throw out bearing area also for wear as that will cause shaft to wobble . I turned a new one from brass bearing I took from metal polishing machine 
Life lesson: If you’re being chased by a lion, you’re on a horse, to the left of you is a giraffe and on the right is a unicorn, what do you do? You stop drinking and get off the carousel.
Back to Top
DavidnTenIll View Drop Down
Bronze Level Access
Bronze Level Access
Avatar

Joined: 02 Nov 2014
Location: illinois
Points: 65 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DavidnTenIll Quote  Post ReplyReply Direct Link To This Post Posted: 23 Jul 2016 at 7:30pm
Yep contacted GG but haven't heard anything back yet. Appreciate the responses.
Back to Top
gemdozer View Drop Down
Orange Level
Orange Level


Joined: 17 Sep 2009
Points: 1072 		Post Options Post Options   Thanks (0) Thanks(0)   Quote gemdozer Quote  Post ReplyReply Direct Link To This Post Posted: 24 Jul 2016 at 10:03am
I have a cluch shaft 19inchs longues and have 1 yoke with U bolts and 1 with joint bolt on yoke
Back to Top
DavidnTenIll View Drop Down
Bronze Level Access
Bronze Level Access
Avatar

Joined: 02 Nov 2014
Location: illinois
Points: 65 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DavidnTenIll Quote  Post ReplyReply Direct Link To This Post Posted: 24 Jul 2016 at 4:55pm
Gem dozer I sent you message should be in your inbox. David.
Back to Top
DavidnTenIll View Drop Down
Bronze Level Access
Bronze Level Access
Avatar

Joined: 02 Nov 2014
Location: illinois
Points: 65 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DavidnTenIll Quote  Post ReplyReply Direct Link To This Post Posted: 27 Jul 2016 at 4:34pm
Gem dozer sent you message and email to your inbox.
David.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.086 seconds.


Help Support the
Unofficial Allis Forum