This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


leaky WD hydraulic pump plugs - help
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
troy(el paso, il) View Drop Down
Silver Level
Silver Level


Joined: 28 Sep 2009
Points: 124 		Post Options Post Options   Thanks (0) Thanks(0)   Quote troy(el paso, il) Quote  Post ReplyReply Direct Link To This Post Topic: leaky WD hydraulic pump plugs - help
    Posted: 17 Mar 2010 at 3:08pm
Hello All-
 
I just put my rebuilt hydraulic pump back on my WD and tested it out, and found that one of the plugs (with the copper gasket?) on top of the pump is leaking.  It seems nice and snug, but it's leaking around that gasket.  It's one of the plugs that can't be pulled out without pulling the hold positon valve assembly off.   I was just wondering if there is any way to seal it externally without having to pull everything apart......Thanks...
 
Troy
Back to Top
Sponsored Links


Back to Top
Lonn View Drop Down
Orange Level
Orange Level
Avatar

Joined: 16 Sep 2009
Location: Назарово,Russia
Points: 29782 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lonn Quote  Post ReplyReply Direct Link To This Post Posted: 18 Mar 2010 at 5:19am
Either tighten it some more and if that don't work replace the copper gasket.
-- --- .... .- -- -- .- -.. / .-- .- ... / .- / -- ..- .-. -.. . .-. .. -. --. / -.-. .... .. .-.. -.. / .-. .- .--. .. ... -
Wink
I am a Russian Bot
Back to Top
CTuckerNWIL View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: NW Illinois
Points: 22823 		Post Options Post Options   Thanks (0) Thanks(0)   Quote CTuckerNWIL Quote  Post ReplyReply Direct Link To This Post Posted: 18 Mar 2010 at 7:23am
If you have to take it off and replace the ring, make sure that both mating surfaces are clean and free of nicks or burrs before reassembly.
http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF
Back to Top
acisbest View Drop Down
Bronze Level
Bronze Level


Joined: 09 Oct 2009
Location: SE, PA
Points: 140 		Post Options Post Options   Thanks (0) Thanks(0)   Quote acisbest Quote  Post ReplyReply Direct Link To This Post Posted: 18 Mar 2010 at 7:49am
You might want to tap the plug once its tight (Lightly Tap, not hammer). The tapping might help flatten out the washer and set it in place? After tapping, see if you can snug it some more. 
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.062 seconds.


Help Support the
Unofficial Allis Forum