This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


1500 Min-Til
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
orangereborn View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: NW WI
Points: 1450 		Post Options Post Options   Thanks (0) Thanks(0)   Quote orangereborn Quote  Post ReplyReply Direct Link To This Post Topic: 1500 Min-Til
    Posted: 05 Feb 2010 at 5:53pm
I picked up a 11 shank 1500 Min-Til that needs a little TLC.  Can someone give measurements/comparison for the hole size in the hanger/support and the pins on the bearing carrier/hsg.  Fab shop says he can make them look like new, but wants to know what new was.  Picture shows what exists now.  Thanks....Dale
Back to Top
Sponsored Links


Back to Top
Skyhighballoon(MO) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Pilot Grove, MO
Points: 3115 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Skyhighballoon(MO) Quote  Post ReplyReply Direct Link To This Post Posted: 05 Feb 2010 at 6:02pm
Dale - oh what a tease  you are with that D21 barely visible in the background!!!!!  Mike
1981 Gleaner F2 Corn Plus w 13' flex
1968 Gleaner EIII w 10' & 330
1969 180 gas
1965 D17 S-IV gas
1963 D17 S-III gas
1956 WD45 gas NF PS
1956 All-Crop 66 Big Bin
303 wire baler, 716H, 712H mowers
Back to Top
orangereborn View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: NW WI
Points: 1450 		Post Options Post Options   Thanks (0) Thanks(0)   Quote orangereborn Quote  Post ReplyReply Direct Link To This Post Posted: 05 Feb 2010 at 8:46pm

Oh no.  Darrell (WA)-don't look.  :)
Back to Top
Kurzy View Drop Down
Orange Level
Orange Level


Joined: 02 Nov 2009
Location: WSS, Montana
Points: 808 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Kurzy Quote  Post ReplyReply Direct Link To This Post Posted: 06 Feb 2010 at 7:08am
Dale,
I would'nt get excited with that hole. Most had room to move around a bit. I don't think they were tight from factory.
 
Kurzy
Back to Top
SCPAAndy View Drop Down
Orange Level
Orange Level


Joined: 05 Dec 2009
Location: East Berlin, PA
Points: 209 		Post Options Post Options   Thanks (0) Thanks(0)   Quote SCPAAndy Quote  Post ReplyReply Direct Link To This Post Posted: 06 Feb 2010 at 6:34pm
dale, they were like you pictured from factory.  we have a mounted tool bar on the rear of ours which has oversized danish tines and a spring loaded buster bar.  We run the the widest and most aggressive points avaiable on our chisel shanks for more soil disturbance.  The one thing we added to our was an additional spring hanger and bearing in the middle of our center disc gang.  Depending on you soils we had trouble with our center gang breaking bc of the lack of support. 
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.062 seconds.


Help Support the
Unofficial Allis Forum