This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Battery corrosion on D19 |
Post Reply |
Author | |
Model 70
Bronze Level Joined: 09 Jan 2021 Location: Minnesota Points: 139 |
Post Options
Thanks(0)
Posted: 05 Nov 2024 at 7:55pm |
So I have a D19 that I’ve switched to negative ground and it charges perfectly but for some reason I get an excessive amount of corrosion on the terminals,battery tray and below the tray on the side panels and anywhere there’s a bare spot where the paint is chipped,even the bolt heads. Any idea. Thanks in advance
|
|
Sponsored Links | |
Ed (Ont)
Orange Level Joined: 08 Nov 2009 Location: New Lowell, Ont Points: 1290 |
Post Options
Thanks(0)
|
Probably not much. Clean everything up well. Use a weak baking soda solution to clean all the acid up and do that once or twice a year. Apparently negative ground systems are worse than positive ground for this problem. Also make sure you are not in an overcharge situation as that will make it worse - leakage at battery. Make sure the grounds are good and clean at both ends of the cables.
|
|
Model 70
Bronze Level Joined: 09 Jan 2021 Location: Minnesota Points: 139 |
Post Options
Thanks(0)
|
Thanks for the advice. I’ll give it a try
|
|
Oldwrench
Bronze Level Joined: 12 Jan 2020 Location: Northeast Points: 131 |
Post Options
Thanks(0)
|
I realize battery polarity discussions can get worse than oil threads, however I had always read that the reason for positive ground polarity for most vehicles before the 60's was reduced body corrosion. Not sure what the compelling reasons were for switching to negative polarity around the early 60's.
|
|
darrel in ND
Orange Level Joined: 22 Nov 2009 Location: Hebron, ND Points: 8634 |
Post Options
Thanks(0)
|
X2, I heard that same theory. Right or wrong though, negative ground definitely won over as the standard of the industry. Darrel |
|
Model 70
Bronze Level Joined: 09 Jan 2021 Location: Minnesota Points: 139 |
Post Options
Thanks(0)
|
That’s interesting to know, I’m really thinking of switching it back to a generator and positive ground.
|
|
injpumpEd
Orange Level Access Joined: 13 Sep 2009 Location: Walnut IL Points: 4917 |
Post Options
Thanks(0)
|
Check the charging system output, my guess is it's over charging and boiling the battery.
|
|
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!
|
|
steve(ill)
Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 81282 |
Post Options
Thanks(0)
|
Key Points
|
|
Like them all, but love the "B"s.
|
|
steve(ill)
Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 81282 |
Post Options
Thanks(1)
|
Check your charge rate for being HIGH... make sure TERMINALS are LEAD and not COPPER..
|
|
Like them all, but love the "B"s.
|
|
Les Kerf
Orange Level Joined: 08 May 2020 Location: Idaho Points: 784 |
Post Options
Thanks(0)
|
Anything that you can do to preserve this irreplaceable jewel is well worth the effort. As others have mentioned, it is likely over-charging. If the tractor is used for field work where it makes long runs between startups, 14.0 Volts is great gobs of plenty, 13.8 Volts is actually sufficient to keep the batteries up. Also consider switching to a sealed AGM type of battery. Yes, they are expensive. So is rotting away your precious Allis. The positive-ground generator was adequate for many years so there is no reason it cannot still git'er done.
|
|
Model 70
Bronze Level Joined: 09 Jan 2021 Location: Minnesota Points: 139 |
Post Options
Thanks(0)
|
K
Edited by Model 70 - 07 Nov 2024 at 7:36am |
|
Model 70
Bronze Level Joined: 09 Jan 2021 Location: Minnesota Points: 139 |
Post Options
Thanks(0)
|
Trying to post a picture of it on here but it keeps telling me that the file size is to big ?
|
|
steve(ill)
Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 81282 |
Post Options
Thanks(0)
|
most cameras take photos that are 4000 x 3000 pixels and 5 Mb in size.. Email to yourself and shring or put on the computer and open in PAINT and resize to about 800 x 600 pixels and 100 kb in size and then the site will accept it.
Facebook and some others will "resize to fit" for you... this site will not do that. Edited by steve(ill) - 06 Nov 2024 at 6:28pm |
|
Like them all, but love the "B"s.
|
|
Model 70
Bronze Level Joined: 09 Jan 2021 Location: Minnesota Points: 139 |
Post Options
Thanks(0)
|
Ok. Thanks Steve
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |