| Author |
 Topic Search  Topic Options
|
HudCo 
Orange Level
Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3940
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: 21" tool box
Posted: 04 Nov 2023 at 10:53pm |
|
when did they start putting the 21 inch long tool box othe d 17 tractor the series 4 parts tractor that i got has that. it will hold somthing
|
 |
|
Sponsored Links
|
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 22074
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Nov 2023 at 11:02pm |
|
My series 3 had the long tool box, only on the right side instead of the left. It will hold the official wheel tread wrenches it is that long.
|
|
HudCo
Orange Level
Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3940
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Nov 2023 at 7:27pm |
|
my series 1 is going to get that long tool box
|
|
AC720Man
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 5246
|
Post Options
Thanks(0)
Quote Reply
Posted: 06 Nov 2023 at 5:16pm |
|
My series 1 had one when I purchased it, bottom was pretty rusted out so I replaced it with a new one. Not sure if the long box came from the factory on a series 1 but it fit perfect. And yes, it holds a lot of tools.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
IBWD MIke
Orange Level
Joined: 08 Apr 2012
Location: Newton Ia.
Points: 4110
|
Post Options
Thanks(0)
Quote Reply
Posted: 07 Nov 2023 at 8:00am |
|
All right, anyone ever put one of these on a WD or 45? Probably be kind of in the way I would guess. Bigger toolbox would be nice on these old girls.
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 22074
|
Post Options
Thanks(0)
Quote Reply
Posted: 07 Nov 2023 at 8:05am |
|
If you located the rear edge of the box in the same place and extended the extra length forward, you'd be alright. I think the lift arm latch comes kinda close when the arms are fully up as it is.
|
|
IBWD MIke
Orange Level
Joined: 08 Apr 2012
Location: Newton Ia.
Points: 4110
|
Post Options
Thanks(0)
Quote Reply
Posted: 07 Nov 2023 at 8:16am |
|
I could check out the lift-arm/latch thing here in just a bit. I only have the one 21" box and it's rusted on the 17b pretty good. Maybe remove it and hold it up for comparison. If I wind up keeping this series 3, which is a pretty good possibility, it will need a new box.
|
|
IBWD MIke
Orange Level
Joined: 08 Apr 2012
Location: Newton Ia.
Points: 4110
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Nov 2023 at 9:05am |
|
Yesterday I checked this out. Raised the plow fully up, measured the three inches on each end, plenty of room. Now I just need to procure a new box or two!
|
|
HudCo
Orange Level
Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3940
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Nov 2023 at 11:04pm |
|
it would be nice looking mounted on the frame rail of a wd
|
|
