This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


#2 plow with hyd lift
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3543 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Topic: #2 plow with hyd lift
    Posted: 17 Apr 2017 at 9:47am
late last fall i bought a #2 plow the leaver on the left side was torched off and the trip too raise it wired open it had some brackets bolted on in the center of the plow frame for a cylinder so i put a lift cylinder of a parts wd on it  .    my question is how do you adjust the depth  .   was this an option ?  how is it to set up ?  any  one have some pictures ? 
Back to Top
Sponsored Links


Back to Top
CrestonM View Drop Down
Orange Level
Orange Level
Avatar

Joined: 08 Sep 2014
Location: Oklahoma
Points: 8391 		Post Options Post Options   Thanks (0) Thanks(0)   Quote CrestonM Quote  Post ReplyReply Direct Link To This Post Posted: 17 Apr 2017 at 9:54am
Sounds like a farmer mod. I would imagine you would put a stop on the cylinder for depth, or just use your hyd lever. 

Edited by CrestonM - 17 Apr 2017 at 9:55am
Back to Top
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3543 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Posted: 17 Apr 2017 at 12:52pm
brackets look like it could have been a kit and oe paint the only things on here that have another coat of paint is what i   repaired .  if this was shop built all of the brackets were drilled and bent in a large press all of the plow frame was drilled . the part in the middle that hooks between the cylinder and the rear or left axle is a cast iron piece that looks like a giant rocker arm and has 314679 cast in it
Back to Top
Bill Long View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Bel Air, MD
Points: 4556 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Bill Long Quote  Post ReplyReply Direct Link To This Post Posted: 17 Apr 2017 at 1:43pm
This is from memory only.  Near the end of our dealership I seem to remember that the #2 plow could be equipped with a hyd lift.  I think it was for raising and lowering only.  I do think the two leavers were still on the plow.  One for the depth and one for the leveling.
Remember, this is from memory only but it is the best I can do.
Hope it is some help.
Good Luck!
Bill Long
Back to Top
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3543 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Posted: 17 Apr 2017 at 9:17pm
it looks to me like when you raise and lower the plow with the hyd the leaver goes up and down the full range of that quadrat ,  i must have that bar from the wheel  to the leaver hooked up wrong
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.084 seconds.


Help Support the
Unofficial Allis Forum