| Author |
 Topic Search  Topic Options
|
00transamnh 
Silver Level
Joined: 15 Sep 2016
Location: Maine
Points: 55
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: B timing cover bolt torque
Posted: 23 Oct 2016 at 11:49am |
|
Anyone have a torque spec for the timing cover bolts for a B?
|
 |
|
Sponsored Links
|
|
|
Hubert (Ga)engine7
Orange Level
Joined: 12 Sep 2009
Location: Jackson Cnty,GA
Points: 6293
|
Post Options
Thanks(0)
Quote Reply
Posted: 23 Oct 2016 at 1:07pm |
|
The IT manual I have does not give a specific torque but I would say just a bit past snug; you don't want the bolts working loose but neither do you want to warp the cover. A thin paper gasket will tolerate a lot more torque than a thicker cork gasket. The manual did state that there a 3 different length bolts that need to go in the proper location. This older equipment is a lot more forgiving of inaccurate torque than what is out there today, most of the old farmers didn't even own a torque wrench. That being said, you won't go wrong by using one.
|
|
Just an old country boy saved by the grace of God.
|
|
Dick L
Orange Level
Joined: 12 Sep 2009
Location: Edon Ohio
Points: 5087
|
Post Options
Thanks(0)
Quote Reply
Posted: 23 Oct 2016 at 1:11pm |
|
I never use torque wrench. You need tighten enough so they are past snug. If you tighten enough to bend the top down at the bolts it is to much and will leak.
|
|
Ted in NE-OH
Orange Level
Joined: 12 Nov 2009
Location: Austinburg OH
Points: 1703
|
Post Options
Thanks(0)
Quote Reply
Posted: 23 Oct 2016 at 8:07pm |
|
good and snug but don't over tighten
|
|
CA, WD, C, 3 Bs, 2 Gs, WC, I-400, 914
|
|
Brian Jasper co. Ia
Orange Level
Joined: 11 Sep 2009
Location: Prairie City Ia
Points: 10508
|
Post Options
Thanks(0)
Quote Reply
Posted: 24 Oct 2016 at 10:25am |
|
Keep in mind there was a special tool required to align the cover for the front crank seal. When I overhauled my CA engine I noticed there were no alignment dowels. It was also much easier to install the new seal with the cover off the engine. To align it I stood the engine on the flywheel end and allowed the seal to position the cover. Hasn't leaked a drop in nearly 20 years.
|
|
"Any man who thinks he can be happy and prosperous by letting the government take care of him better take a closer look at the American Indian." Henry Ford
|
|
Brian Jasper co. Ia
Orange Level
Joined: 11 Sep 2009
Location: Prairie City Ia
Points: 10508
|
Post Options
Thanks(0)
Quote Reply
Posted: 24 Oct 2016 at 10:26am |
|
Now that I think about it, I think somebody made an alignment tool, might have been from a piece of PVC pipe. Might have been Don Bradley...
|
|
"Any man who thinks he can be happy and prosperous by letting the government take care of him better take a closer look at the American Indian." Henry Ford
|
|
Allis dave
Orange Level
Joined: 10 May 2012
Location: Northern IN
Points: 2917
|
Post Options
Thanks(0)
Quote Reply
Posted: 24 Oct 2016 at 10:29am |
|
Don made one out of PVC. It's in his oil pan gasket video. I made one too out of a lock collar.
|
|
