| Author |
 Topic Search  Topic Options
|
Ryan Renko 
Orange Level
Joined: 12 Sep 2009
Location: Edwardsville, I
Points: 2336
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Air compressor issue
Posted: 12 Sep 2018 at 8:21pm |
|
I have a 60 gallon Ingersoll Rand SS-5 compressor that is about 8 years old. Very little use and well maintained. Every thing was great until the last week. It runs as it always did until it reaches around 100psi in the tank and then it falls on its face and the motor bogs down and the belt even starts slipping!! If the breaker doesn't trip after about 10 seconds of this belt squealing it will pick right back up u til it shuts off. Any ideas on this? Thanks in advance, Ryan
|
 |
|
Sponsored Links
|
|
|
jaybmiller
Orange Level Access
Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 24767
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Sep 2018 at 8:34pm |
Have you drained the water from the tank recently ? Have you replaced the belt and adjusted for proper tension ? Any slipped belt will become 'glazed', so not as 'grippy' as it's supposed to be so when the motor sees extra load( 100 PSI), it'll 'stall' out. Not the right 'engineering' terms but...hopefully you get the drift..
Jay
|
|
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)
Never burn your bridges, unless you can walk on water
|
|
Ryan Renko
Orange Level
Joined: 12 Sep 2009
Location: Edwardsville, I
Points: 2336
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Sep 2018 at 8:40pm |
|
I relocated the factory drain valve so it is out front and it is drained after every use. The belt seems as tight as it should be. This issue just rapidly started happening and I am needing advice before I call the company. Ryan
Edited by Ryan Renko - 12 Sep 2018 at 8:41pm
|
|
farmboy520
Orange Level Access
Joined: 22 Jun 2016
Location: Beason, IL
Points: 553
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2018 at 12:06am |
|
I wonder if the check valve that is after the compressor and before the tank is operating correctly?
|
|
shameless dude
Orange Level
Joined: 10 Apr 2017
Location: east NE
Points: 13607
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2018 at 3:23am |
|
try adjusting the PSI down a little bit
|
|
CrestonM
Orange Level
Joined: 08 Sep 2014
Location: Oklahoma
Points: 8457
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2018 at 10:02am |
 farmboy520 wrote:
I wonder if the check valve that is after the compressor and before the tank is operating correctly? |
Grandpa has an air compressor from the '50s and it has this problem sometimes.
|
|
desertjoe
Orange Level Access
Joined: 23 Sep 2013
Location: New mexico
Points: 13729
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2018 at 10:11am |
Well,,I started havin the same issue with my compressor couple weeks ago and I figured it was the motor as it is very old,,,,but since that time it has been runnin just like old times,,,,WHH,,,,???
|
|
Bill_MN
Orange Level
Joined: 12 Sep 2009
Location: Sioux Falls, SD
Points: 1471
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2018 at 3:44pm |
|
I agree with the check valve issue, it is getting some back pressure above 100 psi and the pump is trying to push against a closed/part closed valve. Could be a broken or corroded spring that all of a sudden let go, I imagine that would be an fairly cheap part.
|
|
1951 WD #78283, 1918 Case 28x50 Thresher #76738, Case Centennial B 2x16 Plow
|
|
chaskaduo
Orange Level
Joined: 26 Nov 2016
Location: Twin Cities
Points: 5200
|
Post Options
Thanks(0)
Quote Reply
Posted: 13 Sep 2018 at 4:28pm |
|
Aunt Peg would say they are sending cheap electricity and charging premium price.
|
|
1938 B, 79 Dynamark 11/36 6spd, 95 Weed-Eater 16hp, 2010 Bolens 14hp
|
|
