| Author |
 Topic Search  Topic Options
|
Reindeer 
Orange Level
Joined: 14 Sep 2009
Location: Calgary, AB
Points: 650
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: 110v electric starter problem on a snowblowe motor
Posted: 26 Jan 2020 at 2:14pm |
|
So I picked up a snow blower with a 10.5 horse Tecumseh Motor. With a few parts and fresh oil everything works pretty good, but it has one of those plug in starters, which I would like to use. The starter turns fine, but the bendix gear had lost a few teeth. Bought a replacement off Ebay and afer a couple of tries managed to get the right gear. Assembled everything and it spins just fine, but hte gear does not move out to engage the ring gear on the flywheel. The original gear was cast and I suspect the new one is sintered metal, so lighter. Could that be the problem. The bendix moves out on the shaft to engage the ring gear, along a threaded portion of hte shaft, and if it is lighter perhaps there is not enough inertia to get it out where it needs to be? Anyone have any suggestions?
Edited by Reindeer - 26 Jan 2020 at 2:45pm
|
|
|
 |
|
Sponsored Links
|
|
|
Dave in PA
Orange Level
Joined: 13 Sep 2009
Location: Mars/Wexford PA
Points: 2627
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jan 2020 at 3:01pm |
|
??? good question! If all is free, and moving, it should work. I have seen a few, even with plastic gears work. ???? sorry that I have not a clue here.
|
|
nella(Pa)
Orange Level Access
Joined: 11 Sep 2009
Location: Allentown, Pa.
Points: 3102
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jan 2020 at 3:01pm |
|
Repaired a Craftsman snow blower for a friend, sounds like the same motor, teeth were missing on the bendix gear, got a starter from eBay for $50 and Sears wanted $181 for the exact same starter(part number).
|
|
Dakota Dave
Orange Level
Joined: 12 Sep 2009
Location: ND
Points: 3938
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jan 2020 at 3:03pm |
|
You van get just the gear from jacks small engines it show up a vouple days after you order it
|
|
jaybmiller
Orange Level Access
Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 22452
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jan 2020 at 3:31pm |
Maybe it's NOT the correct starter ! If you manually turn the starter, does the ger go up to the correct height? Is the flywheel all the way down ? You should see the 'wear' marks on the flywheel where the starter gear had been meshing. One of those have to see to figure it out problems.
Edited by jaybmiller - 26 Jan 2020 at 4:10pm
|
|
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)
Never burn your bridges, unless you can walk on water
|
|
Dave in PA
Orange Level
Joined: 13 Sep 2009
Location: Mars/Wexford PA
Points: 2627
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jan 2020 at 3:39pm |
|
GOOD info! Techjunka, had 2 different starters from my memory, a long and a short. Might just be the issue. OPPS, did ya see that I really don't like them?? lol
|
|
chaskaduo
Orange Level
Joined: 26 Nov 2016
Location: Twin Cities
Points: 5200
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jan 2020 at 3:44pm |
Are all the parts there? [TUBE]QaPwOR6VwVg[/TUBE]
|
|
1938 B, 79 Dynamark 11/36 6spd, 95 Weed-Eater 16hp, 2010 Bolens 14hp
|
|
Dave in PA
Orange Level
Joined: 13 Sep 2009
Location: Mars/Wexford PA
Points: 2627
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jan 2020 at 3:51pm |
|
"Donyboy73", is top notch for repairs, as well as "taryl fixes all". both with lots of knowledge!!
|
|
jaybmiller
Orange Level Access
Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 22452
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jan 2020 at 4:17pm |
gee, watched the video, there's a REAL tool for removing/installing the ring clip !!!????  I've always used screwdriver to get off - socket to whack on.....
If you were up for a roadtrip, I've got 2 starters on the shelf.....  at least you're on OUR side of the 49th !!
|
|
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)
Never burn your bridges, unless you can walk on water
|
|
ac fleet
Orange Level
Joined: 12 Jan 2014
Location: Arrowsmith, ILL
Points: 2316
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Jan 2020 at 4:22pm |
As stated, Tech. used different ones. --- Make sure you have the right one to start with. Next would be to make sure it has the right worm end that runs the gear up! IF the track gets worn, the gear binds!
These 110-v starters kick ass, so if it don't engage I would suspect the shaft is damaged! I have one with a plastic gear and it works fine, so I don't think you have a weight problem!
Try putting some slick-um on the shaft just to test if that will make it go. Check the spring and keepers to see that they are in the right places.
|
|
http://machinebuildersnetwork.com/
|
|
mdm1
Orange Level
Joined: 12 Sep 2009
Location: Onalaska, WI
Points: 2634
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Jan 2020 at 10:53am |
|
I just took mine off of the snowblower. Gear spun but didn't move up the shaft to engage flywheel. Lubed the shaft alittle and it works fine. Maybe I just got lucky.
|
|
Everything is impossible until someone does it! WD45-trip loader 1947 c w/woods belly mower, 1939 B, #3 sickle mower 1944 B, 2 1948 G's. Misc other equipment that my wife calls JUNK!
|
|
trace
Silver Level
Joined: 01 Aug 2012
Location: N.W. Iowa
Points: 499
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Jan 2020 at 3:39pm |
|
techumsa motors suck.
|
|
1955 WD-45 WIDE FRONT W/ TRIP
LOADER
|
|
shameless dude
Orange Level
Joined: 10 Apr 2017
Location: east NE
Points: 13607
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Jan 2020 at 10:25pm |
|
BIL has same problem with his Tecumsa powered snowblower
|
|
Ray54
Orange Level Access
Joined: 22 Nov 2009
Location: Paso Robles, Ca
Points: 4516
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Jan 2020 at 10:34am |
 shameless dude wrote:
BIL has same problem with his Tecumsa powered snowblower |
He will be OK if don't aim the "pretty machine" at him.
|
|
