WANTED - Model #82 Sickle Bar Guards
Printed From: Unofficial Allis
Category: Other Topics
Forum Name: Classifieds
Forum Description: For sale or wanted items
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=193855
Printed Date: 20 Jun 2024 at 10:06am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: WANTED - Model #82 Sickle Bar Guards
Posted By: D17IV
Subject: WANTED - Model #82 Sickle Bar Guards
Date Posted: 03 Mar 2023 at 11:28am
I am looking for 15-original sickle bar mower guards (without replaceable ledger plates) for a model #82 mower. Thank you in advance. Brian from Ohio.
-------------
B110, 1937 WC, CA, 2-WD45 Diesels, D14, 2-D15 Series II and 2-D17IV
|
Replies:
Posted By: PaulB
Date Posted: 03 Mar 2023 at 11:55am
Are you looking for NOS or used take offs?
-------------
If it was fun to pull in LOW gear, I could have a John Deere.
If you can't make it GO... make it SHINY
|
Posted By: D17IV
Date Posted: 03 Mar 2023 at 12:01pm
Good used would be fine. Possibly NOS depending on the price. Thanks.
-------------
B110, 1937 WC, CA, 2-WD45 Diesels, D14, 2-D15 Series II and 2-D17IV
|
Posted By: Darb210
Date Posted: 03 Mar 2023 at 1:44pm
|
I have an 82S that is without mounting brackets & rear pulley, would part or sell as what's left. Near Pandora OH 45877. A.J. 419-230-3362
|
Posted By: AC720Man
Date Posted: 04 Mar 2023 at 9:31pm
I am in the same position, are the wear plates available to replace? Ford G81-0807 guards are available locally. Just wanting to stay AC. I’m using Hershel serrated sections.
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: Mikez
Date Posted: 04 Mar 2023 at 9:40pm
|
The guards with rivet holding a ledger plate. Yes the ledger is replaceable. I can see if I have any left if you’d like
|
Posted By: AC720Man
Date Posted: 04 Mar 2023 at 10:01pm
Thanks Mike
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: Tracy Martin TN
Date Posted: 04 Mar 2023 at 10:10pm
I use the twin New Holland on mine with 1 AC guard. Works great, mowed a bazillion acres over the years. HTH Tracy
-------------
No greater gift than healthy grandkids!
|
Posted By: AC720Man
Date Posted: 04 Mar 2023 at 10:23pm
I will keep that in mind Tracy. Do you have the guard number in case I can’t get enough ledger plates?
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: AC720Man
Date Posted: 04 Mar 2023 at 10:26pm
What sections are you using Tracy? I’m using Hershel A+
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: Tracy Martin TN
Date Posted: 04 Mar 2023 at 10:41pm
I don't remember on part numbers. The Herschels I use are the same hole spacing as AC are.Those ledger plates are tough to replace correctly. Need a good heavy setup for head side. HTH Tracy
-------------
No greater gift than healthy grandkids!
|
Posted By: AC720Man
Date Posted: 05 Mar 2023 at 12:03am
Part number should be stamped on it. I don’t think the guards on our NH 451 mower will fit but I should check.
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: AC720Man
Date Posted: 05 Mar 2023 at 12:14am
The A+ fits the same hole pattern as the AC sections. Just depends if your using the regular sections or the serrated? Better known as Tiger shark sections they really do a nice job of cutting as long as the ledger plate it good. Especially orchard grass and fine grass as I am used to cutting. I will admit replacing ledger plates is not something I am accustomed to so I am interested to find out how to properly replace them. Otherwise I will need to use replacement guards instead. Thank you Tracy for your wisdom
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: Tracy Martin TN
Date Posted: 05 Mar 2023 at 7:07pm
|
Easiest way is to drive them out from ledger plate side of guard. You can drill counter sink head off if you want to, but takes practice. Need to have the guard you are working on supported well. You can leave on mower, use an anvil or short piece of railroad rail. Needs to be cleared for ledger plate rivet removal. Use a heavy punch with short tip to start them moving. Finish driving it out with longer punch. Shortest length possible. And to replace remove guard, insert ledger plate, install rivet, use a heavy punch or hardy tool in anvil, make sure ledger plate is tight to guard with correct length rivet, pound rivet with hammer, making sure ledger plate is tight to guard during process. HTH Tracy
-------------
No greater gift than healthy grandkids!
|
|