new saw
Printed From: Unofficial Allis
Category: Other Topics
Forum Name: Shops, Barns, Varmints, and Trucks
Forum Description: anything you want to talk about except politics
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=179942
Printed Date: 30 Oct 2025 at 10:05pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: new saw
Posted By: shameless dude
Subject: new saw
Date Posted: 19 Apr 2021 at 2:38am
| earlier i posted about my BOSCH saw nut cutting a true 90 degree cut...i looked it over, i don't/didn't see any more adjustments that i haven't seen before on the saw. still always cuts a 87-89 degree cut. it also isn't big nuff to cut a whole floor board, it leaves about 7/8 of an inch on the board, and no matter how i try to finish the cut, i always hafta gring or sand that part down, soooooo.....i went out and bought a new DEWALT slider saw. it'll cut a true 90 degrees and cut the whole floor board. also it is a 20V battery operated slider saw. guess i'll see how long a battery lasts on it! while i was shopping that day, my back went out in the store, had to keep finding places to land in the store. i could sit awhile then shop awhile, they didn't have any of them hot rod electric shopping carts there. PfffffT! and as i was waiting for the line to check out ahead of me there was a stool there with DEWALT's name on it, i landed on it while waiting. dang that stool was comfy and was the right height for me. my other stools i have are either to short or to tall, this one is adjustable and has a better seat cushion on it...guess it better have for $99. yeah...it came home with me too! just one thing the stimulas check paid for! |
Replies:
Posted By: FREEDGUY
Date Posted: 20 Apr 2021 at 5:18pm
I didn't read/see your initial post about the Bosh being off a few degrees and you not being able to "dial-it-in", but there is an adjustment for that, I'm just not familiar with Bosh to help you out  . You should have been able to hold your floor board tight to the fence and "tip" your board up towards the motor to finish off the cut in one motion  . I "assume" the Bosh is a 10" non-slider ??
|
Posted By: Thad in AR.
Date Posted: 20 Apr 2021 at 5:44pm
|
Well if your new Dewalt is anything like my new 12” Dewalt slider it’s no wonder your back went out. |
Posted By: jaybmiller
Date Posted: 20 Apr 2021 at 5:57pm
|
FIRST job with that new saw..... cut up your dang MACHINE !!!! supposed to get 10-15 sillymeters... SIX friggin INCHES.... grrrrrrrrrrrrrrrrrrrrrrrrrr and BTW, WHO 'borrowed' the power cable off my spare clothes dryer !!!????? ------------- 3 D-14s,A-C forklift, B-112 Kubota BX23S lil' TOOT( The Other Orange Tractor) Never burn your bridges, unless you can walk on water |
Posted By: FREEDGUY
Date Posted: 20 Apr 2021 at 5:57pm
I help a guy that runs a Makita LS1019 slide saw, pretty darn accurate btw, and it weighs almost 70 #'s  .What size is Shameless running ?
|
Thad in AR. wrote:Posted By: Thad in AR.
Date Posted: 20 Apr 2021 at 7:04pm
|
I have a Mikita LS slider and my new Dewalt outweighs it. The Mikita is still a good saw but has a lot of miles on it. I only bring the new one out on big trim jobs. It’s bolted to a Dewalt stand on wheels and easy to move but takes up a lot of room. The Mikita quick releases from its stand and takes up much less room. Both big and bulky. |
Posted By: FREEDGUY
Date Posted: 20 Apr 2021 at 7:18pm
Thanks Thad. The older I get, the heavier they ALL get
 ! |
Posted By: Thad in AR.
Date Posted: 20 Apr 2021 at 7:32pm
That’s for sure. I used to haul a belt drive table saw all over creation. Was a happy day when I got a decent folding job saw. Now I want one of those light aluminum air compressors. |
Posted By: shameless dude
Date Posted: 22 Apr 2021 at 12:17am
| i almost need a forklift to move the BOSCH saw around. the new DEWALT is alot lighter, i haven't used it yet, been to cold to sit outside to use it. i don't wanna blow sawdust all over inside the cook shack. so far...as soon as it warms up a bit i gotta play with the new saw, and the new air powered brad nailer i gots too. ya'll spose i can nail the old ladys.....oooops....i mean the loving wifes shoes to the floor? did that to my boss once on a const site! lol |
Posted By: JohnColo
Date Posted: 22 Apr 2021 at 12:30am
|
Was he wearing them at the time? |
Posted By: shameless dude
Date Posted: 22 Apr 2021 at 11:48pm
| yes he was John! we was up ona roof and he was yelling at all us, he came to close to me...oooops....break time....we left and he was still up there trying to gits loose! neighbors heard lots of ugly words that day! he finally got down, but one of his boots was still up there! he never came back up on the roof after that! |
Posted By: Ray54
Date Posted: 23 Apr 2021 at 11:32am
 We will miss you , just saying good by in case you just cannot help yourself and nail the ol......................loving wife's shoes down.
|
Posted By: shameless dude
Date Posted: 24 Apr 2021 at 12:04am
| if the opertunity arises..... |
Posted By: Ted J
Date Posted: 25 Apr 2021 at 11:29pm
|
Good thing you ended with her shoes..... ------------- "Allis-Express" 19?? WC / 1941 C / 1952 CA / 1956 WD45 / 1957 WD45 / 1958 D-17 |