Cab interior kits for 8000 series
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=156176
Printed Date: 14 Nov 2024 at 9:03am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: Cab interior kits for 8000 series
Posted By: WD45
Subject: Cab interior kits for 8000 series
Date Posted: 05 Dec 2018 at 3:22pm
|
Comments, source and price for cab kit for Allis 8000 cab. Also the deluxe brown plaid seat cover. The cab kits from Shoup would these be Fehr? Has anyone used Shoup cab kits and how did they fit and look.
------------- Fred Dunlop, G,B,CA, WC,WF, 3 WD45`s,gas, diesel and LP,U,D10 series III, D12,D14,D15 SERIES II,D17 Series IV in Gas and Diesel ,D19 GAS and D21,170 185,210 ,220 an I-600 8070 fwd, 716H and 1920H |
Replies:
Posted By: Daehler
Date Posted: 05 Dec 2018 at 7:14pm
|
Fehr cab interiors is where I've purchased 2 kits from, roughly $500 will do top and bottom. Highly recommend them. Kits are close to perfect match except the posts where a little big on the two I purchased from them. They also include glue which is very strong in bonding. Their window seal kit is a dead on match too. As for seat cloth, good luck. I haven't been able to find a textile place to reproduce it. It someone knew of a place to get it reproduced, I would gladly send a old cover to them to get the pattern copied. ------------- 8070FWA,7080 BlackBelly, 7045,2 200s,D19,D17,G, WD,45,UC,7 AC mowers and lots more! "IT TAKES 3 JD's TO OUT DO AN ALLIS, 2 TO MATCH IT IN THE FIELD AND 1 FOR PARTS!" |
Posted By: DSeries4
Date Posted: 05 Dec 2018 at 8:35pm
|
Ivan Summerix in Michigan is supposed to have seat covers that are very close to original. I must also give a thumbs up to the Fehr cab kits. Finished putting one in my 6080 a few months ago. Very good quality! ------------- '49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '61 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080 |
Posted By: Unit3
Date Posted: 05 Dec 2018 at 9:15pm
|
Try Hy-Capacity out of Humboldt, Iowa. I have used them in both of the 8070's. Drill out the rivets in the two strips at the right side up high at the door and rear side window and the headliner will come down easier. When installing the foam, I dry fit things first. I started at the bottom and worked my way up. In dad's 8050, the owner before us started at the top and went down. The two pieces on the post were stuffed together and it looks bad. If they would have started with the large fender piece, then the small piece on the post, anything extra on the post could have been tucked up under the headliner and the fit would have been perfect. Hope this helps. ------------- 2-8070FWA PS/8050PS/7080/7045PS/200/D15-II/2-WD45/WD/3-WC/UC/C |
Posted By: Steve Bright
Date Posted: 09 Dec 2023 at 9:04pm
| Where do you get the straps to pull the doors shut? |
Posted By: Kenny L.
Date Posted: 09 Dec 2023 at 9:41pm
|
I use Hi Capacity for the upper part and a Ferh floor mat on my 8030. |
Posted By: Kenny L.
Date Posted: 09 Dec 2023 at 9:44pm
Steve I found my at a salvage yard, take a drill and drill bits make it a lot easier to remove them.
|
Steve Bright wrote:Posted By: 8070nc
Date Posted: 09 Dec 2023 at 10:07pm
|
The pull strap on a 73-87 chevy pickup is a decent replacement. It would need to be cut but they could be made to work ------------- 1984 80780 1957 D14 DES 300 with 25000 engine 616 tractor |
Posted By: AC7060IL
Date Posted: 10 Dec 2023 at 7:33am
|
WD45, Here’s a March 2021 link to PaFarmer’s 8070 restoration. Similar discussions & ideas in it. https://www.allischalmers.com/forum/8070-restoration_topic179118_page1.html" rel="nofollow - https://www.allischalmers.com/forum/8070-restoration_topic179118_page1.html |