| Author |
 Topic Search  Topic Options
|
TomYaz 
Orange Level
Joined: 14 Sep 2009
Location: PA
Points: 10330
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: All-Crop snap coupler grain drill.
Posted: 5 hours 23 minutes ago at 11:15am |
Question on its operation...
Is the use of the hydraulic "hold position" necessary to use this unit, or is just a drop to the ground deal?
Thinkin about getting one to play with but I despise the hold position setting on the WD45......
|
|
If its not an All-Crop, it all crap!
|
 |
|
Sponsored Links
|
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8488
|
Post Options
Thanks(0)
Quote Reply
Posted: 3 hours 16 minutes ago at 1:22pm |
|
Only other thing you can do is set it for TB. Realize that it will drop quicker with less control and lever has to be full up all the while when raised. What's the issue with hold position?
|
|
Allis dave
Orange Level
Joined: 10 May 2012
Location: Northern IN
Points: 2974
|
Post Options
Thanks(0)
Quote Reply
Posted: 3 hours 13 minutes ago at 1:25pm |
It's not suggested to use the TB setup and use it to hold up equipment for long periods of time. DR has advised against this.
I also find the hold positon odd and annoying, but I was usint it once while disking and left it up for a but and it locked up the hydraulics. Everything was stuck "up". U had to loosen the coupler to relieve pressure to get everything working again.
I suppose I find it annoying becasue the hold detent is so strong. It's difficult to jerk it up and down for a minor adjustment.
|
|
TomYaz
Orange Level
Joined: 14 Sep 2009
Location: PA
Points: 10330
|
Post Options
Thanks(0)
Quote Reply
Posted: 2 hours 39 minutes ago at 1:59pm |
<<It's difficult to jerk it up and down for a minor adjustment.>>
yep...pain when I want to set it up a bit up or down with brush hog. Would think adjusting for a grain drill is more exacting. ...not interested in that...screw it...
|
|
If its not an All-Crop, it all crap!
|
|
Don(MI)
Orange Level
Joined: 15 Sep 2009
Location: Michigan
Points: 3844
|
Post Options
Thanks(0)
Quote Reply
Posted: 2 hours 4 minutes ago at 2:34pm |
|
Tom, the spring coils control about 6-8" of vertical movement on each disc and seed tube across the width of the drill. I would think it's no issue. We have used the same drill on both WD and D14 without any issues on hold positions. I think the vertical travel helps make up any differential with the hold pos. Of the tractor. If that makes sense...
|
|
Galatians 5:22-24
"I got a pig at home in a pen and corn to feed him on, All I need is a pretty little girl to feed him when I'm gone!"
|
|
Don(MI)
Orange Level
Joined: 15 Sep 2009
Location: Michigan
Points: 3844
|
Post Options
Thanks(0)
Quote Reply
Posted: 2 hours 3 minutes ago at 2:35pm |
|
|
|
Galatians 5:22-24
"I got a pig at home in a pen and corn to feed him on, All I need is a pretty little girl to feed him when I'm gone!"
|
|
DiyDave
Orange Level Access
Joined: 11 Sep 2009
Location: Gambrills, MD
Points: 53285
|
Post Options
Thanks(0)
Quote Reply
Posted: 1 hour 20 minutes ago at 3:18pm |
|
If you're looking for one, I have one to sell...
|
|
Source: Babylon Bee. Sponsored by BRAWNDO, its got what you need!
|
|
den/southern illinoi
Orange Level
Joined: 11 Sep 2009
Location: Sparta, Illinoi
Points: 2059
|
Post Options
Thanks(0)
Quote Reply
Posted: 52 minutes ago at 3:46pm |
|
The one I had actually hung off the rock shaft. Just have to adjust the chains to allow the drill to be at the right depth. Do not need to hold with the hydraulics.
|
|
Own 4 wheel 20, 2-5015, 5020 and associated equipment and 2 electric forklifts.
|
|
