Allis CA

Message Rating: Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Paul,Could you post a picture of the B/C side weights used with a longer bolt? Might help someone working on this old iron too.
Folks,
I just cleaned up the longer,  lower steering arm, the side weights, and the knobs they set on. Shot some high build primer on them maybe I can put some of that shiny PO#1 on them soon. The crude paint booth has helped reduce the over spray in the shop a lot! 
This old CA was a misfit when I bought it and hasn't gotten much better in my possession either.
I did talk with Brenda at Sandy Lake Impl. and ordered a seal for the PTO shaft. That may reduce the oil dripping from that area? Still have a pesky leak from one of the rad hose connections. Like most of the other Allis tractors we have, they all mark their territory! 
Also dropped off the IH rear wheel weights to get them cut in half. They have several saws that should make short work of those. I am going to make some brackets and sq tubing to allow our 15 lb weights to be added if needed.

Here is the short arm, key, gear and bolt. It almost fell out of there!:)

The old sandblaster helps clean these items back near original condition.

Regards,
 Chris and Cheryl

Edited by Sugarmaker - 17 hours 9 minutes ago at 3:15pm

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Rating: Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Sugarmaker Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 12 Jul 2013 Location: Albion PA Points: 8509	Post Options Post Reply Quote Sugarmaker Report Post Thanks(0) Quote Reply Posted: 17 hours 14 minutes ago at 3:10pm
	Paul, Could you post a picture of the B/C side weights used with a longer bolt? Might help someone working on this old iron too. Folks, I just cleaned up the longer, lower steering arm, the side weights, and the knobs they set on. Shot some high build primer on them maybe I can put some of that shiny PO#1 on them soon. The crude paint booth has helped reduce the over spray in the shop a lot! This old CA was a misfit when I bought it and hasn't gotten much better in my possession either. I did talk with Brenda at Sandy Lake Impl. and ordered a seal for the PTO shaft. That may reduce the oil dripping from that area? Still have a pesky leak from one of the rad hose connections. Like most of the other Allis tractors we have, they all mark their territory! Also dropped off the IH rear wheel weights to get them cut in half. They have several saws that should make short work of those. I am going to make some brackets and sq tubing to allow our 15 lb weights to be added if needed. Here is the short arm, key, gear and bolt. It almost fell out of there!:) The old sandblaster helps clean these items back near original condition. Regards, Chris and Cheryl Edited by Sugarmaker - 17 hours 9 minutes ago at 3:15pm
	D17 1958 (NFE), WD45 1954 (NFE), WD 1952 (NFE), WD 1950 (WFE), Allis F-40 forklift, Allis CA, Allis D14, Ford Jubilee, Many IH Cub Cadets, 32 Ford Dump, 65 Comet.

Sponsored Links

Sugarmaker Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 12 Jul 2013 Location: Albion PA Points: 8509	Post Options Post Reply Quote Sugarmaker Report Post Thanks(0) Quote Reply Posted: 11 hours 3 minutes ago at 9:21pm
	Guys, I did get the parts painted to put the steering back together. Just like you guys said it steers much better with this long arm installed. Should make a comfortable tractor to handle. The tractor would have worked with the short arm, but it is much better with the change to the long one. A nice ride in the dark down the road was positive. Oh yes the lights work great too. May not win many pulls but will present itself well. Regards, Chris and Cheryl Edited by Sugarmaker - 10 hours 60 minutes ago at 9:24pm
	D17 1958 (NFE), WD45 1954 (NFE), WD 1952 (NFE), WD 1950 (WFE), Allis F-40 forklift, Allis CA, Allis D14, Ford Jubilee, Many IH Cub Cadets, 32 Ford Dump, 65 Comet.

ACinSC Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 16 Dec 2015 Location: South Carolina Points: 2977	Post Options Post Reply Quote ACinSC Report Post Thanks(1) Quote Reply Posted: 7 hours 32 minutes ago at 12:52am
	Looks very nice to me!!

Jgranat Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 25 Mar 2019 Location: NW PA Points: 119	Post Options Post Reply Quote Jgranat Report Post Thanks(0) Quote Reply Posted: 45 minutes ago at 7:39am
	Great job on the CA Chris, start to finish!!