![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
716H wont move |
Post Reply ![]() |
Author | |
Djp9211 ![]() Bronze Level ![]() ![]() Joined: 05 Feb 2022 Location: Illinois Points: 5 |
![]() ![]() ![]() ![]() ![]() Posted: 05 Feb 2022 at 3:20am |
I have a 716h I used yesterday to blow snow pulled it in the garage went out this morning to hop on it to finish blowing the snow off driveway and it won't do anything when you move forward and reverse. Any help would be greatly appreciated!
|
|
![]() |
|
Sponsored Links | |
![]() |
|
oldfords ![]() Bronze Level Access ![]() Joined: 31 Mar 2020 Location: South Dakota Points: 49 |
![]() ![]() ![]() ![]() ![]() |
The first thing I would look at is to make sure the two little plungers under the seat are up. They are located under a spring loaded lever that you push down to free wheel the tractor
|
|
![]() |
|
Mikez ![]() Orange Level Access ![]() ![]() Joined: 16 Jan 2013 Location: Usa Points: 8604 |
![]() ![]() ![]() ![]() ![]() |
welcome to the forum.
Also some time people push clutch brake in and it sticks, so make sure the belt is tight and is spinning the rear pulley and check oil levels.
|
|
![]() |
|
Djp9211 ![]() Bronze Level ![]() ![]() Joined: 05 Feb 2022 Location: Illinois Points: 5 |
![]() ![]() ![]() ![]() ![]() |
I think I found what you're talking about they don't seem to move I took them out to clean but doesn't seem like they come apart should the buttons go down easy or are they stuck? Also have a sound coming from centrifugal clutch and have no pullys spinning
|
|
![]() |
|
Mikez ![]() Orange Level Access ![]() ![]() Joined: 16 Jan 2013 Location: Usa Points: 8604 |
![]() ![]() ![]() ![]() ![]() |
with it running the front pulley off bevel gear box should be spinning. If not check drive shaft off engine. There’s round fiber plates that bolt in between each end of drive shaft. Or maybe bevel gearbox is out.
|
|
![]() |
|
Mikez ![]() Orange Level Access ![]() ![]() Joined: 16 Jan 2013 Location: Usa Points: 8604 |
![]() ![]() ![]() ![]() ![]() |
if your belt isn’t spinning it’s not the buttons. And yes they do stick if you don’t use them. Soak them in penetrating oil
|
|
![]() |
|
Djp9211 ![]() Bronze Level ![]() ![]() Joined: 05 Feb 2022 Location: Illinois Points: 5 |
![]() ![]() ![]() ![]() ![]() |
The drive shaft spins but nothing after that is.turning
|
|
![]() |
|
Mikez ![]() Orange Level Access ![]() ![]() Joined: 16 Jan 2013 Location: Usa Points: 8604 |
![]() ![]() ![]() ![]() ![]() |
bad news then. That gear box is out. And it’s expensive to rebuild. But in my opinion worth fixing the ole girl
|
|
![]() |
|
Djp9211 ![]() Bronze Level ![]() ![]() Joined: 05 Feb 2022 Location: Illinois Points: 5 |
![]() ![]() ![]() ![]() ![]() |
I was afraid of that. Any idea how hard it is to rebuild or replace? Or where to find a new one?
|
|
![]() |
|
Mikez ![]() Orange Level Access ![]() ![]() Joined: 16 Jan 2013 Location: Usa Points: 8604 |
![]() ![]() ![]() ![]() ![]() |
well do you have an old small engine repair shop with experience with them. Or you working on it yourself. If you don’t have parts books, you can look up parts tree. Type in 7016 and look for simplicity and look for bevel gear box. A lot of folks on here use sandy lake implement and ask for Brenda
Edited by Mikez - 07 Feb 2022 at 1:35pm |
|
![]() |
|
DaveWisc. ![]() Orange Level ![]() ![]() Joined: 11 Oct 2009 Location: Wisc. Points: 1008 |
![]() ![]() ![]() ![]() ![]() |
Idk bye could you just replace the box easier
|
|
![]() |
|
ac55tractor ![]() Silver Level ![]() Joined: 20 Oct 2012 Location: Raymond, Maine Points: 240 |
![]() ![]() ![]() ![]() ![]() |
I just searched around for a pair of gears for you. They are not cheap.
You may be better off finding a replacement bevel gear box. They made different boxes for these tractors. Just be careful what you choose. eBay has one for about the price of new gears. I am not recommending that you buy anything. I am just showing you examples. Send me a personal message. I will send you back my email and I will forward a parts manual and operators manual to you. I just tried to send them through the forum, they wouldn't go. Glad to help I have 4 Simplicity Garden tractors here at the house. I have kept them all running for over 25 years now. Simplicity 3510 Simplicity 7013S Simplicity 7016 Simplicity 7016H Steve (in ME) |
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |