This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Why did Deutz kill the 8000 series?
 Post Reply Post Reply Page  <12
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
NEVER green View Drop Down
Orange Level Access
Orange Level Access


Joined: 28 Feb 2013
Location: MN.
Points: 7505 		Post Options Post Options   Thanks (0) Thanks(0)   Quote NEVER green Quote  Post ReplyReply Direct Link To This Post Posted: 28 Mar 2024 at 9:20am
Originally posted by bigal121892 bigal121892 wrote:

According to our Allis dealer at the time, Deutz owned 20% of Steiger; Steiger was going to manufacture row crop tractors for Deutz-Allis, using a Deutz engine. CaseIH threw a monkey wrench into that plan, when they purchased the 80% of Steiger that Deutz didn't own. So, they went shopping for a someone to manufacture a tractor for them. According to our dealer, they went with White for two reasons; (1) Deutz engineers felt only the White rear end could hold up to the low end torque of the Deutz engine, and (2) White was offering them the best warranty.

  Very interesting. I have seen a White ring gear in a 180 hp tractor, they are huge.
2-8050 1-7080 6080 D-19 modelE & A 7040   R50       
Back to Top
Sponsored Links


Back to Top
8070nc View Drop Down
Orange Level Access
Orange Level Access


Joined: 21 Mar 2019
Location: North Carolina
Points: 506 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 8070nc Quote  Post ReplyReply Direct Link To This Post Posted: 28 Mar 2024 at 1:55pm
Just some thoughts on on the 7/8000 rear ends. With all the hours we have put on those tractors kwe never had one apart. Never seen one in a dealership apart. Back in the 1980s id go to the IH dealer for planter parts and the shop would be full of 10, 14, 15, 66 and 86 series with rear ends apart and scattered everywhere
1984 80780
1957 D14
DES 300 with 25000 engine
616 tractor
Back to Top
bigal121892 View Drop Down
Orange Level
Orange Level


Joined: 05 Jan 2010
Location: Nebraska
Points: 803 		Post Options Post Options   Thanks (0) Thanks(0)   Quote bigal121892 Quote  Post ReplyReply Direct Link To This Post Posted: 28 Mar 2024 at 3:02pm
We've had a couple of them apart. On the four pinion differentials, the bolt that holds everything together, (70933256) will break, then a lot of bad things happen.
Back to Top
jdeere562 View Drop Down
Bronze Level
Bronze Level


Joined: 02 Oct 2023
Location: SW Iowa
Points: 31 		Post Options Post Options   Thanks (0) Thanks(0)   Quote jdeere562 Quote  Post ReplyReply Direct Link To This Post Posted: 28 Mar 2024 at 5:29pm
I was an Allis mechanic at two different dealers, from 1975 until 1991.
It was a nightmare with Deutz. Allis had great service manuals. Deutz manuals sucked. Few words and a bunch of symbols. About like a car from the 1960's to that current crap that pops up on the dash today. Stop and read the owner's manual to see what they mean.

Cab heaters run off diesel fuel, what a joke. Cylinder heads with stretch bolts were also a pain. In 1991 I moved on to Deere, and NOT as a mechanic either!
Back to Top
Fred in Pa View Drop Down
Orange Level
Orange Level
Avatar

Joined: 13 Sep 2009
Location: Hanover Pa.
Points: 9210 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Fred in Pa Quote  Post ReplyReply Direct Link To This Post Posted: 29 Mar 2024 at 6:33am
Allis killed Allis when they SOLD to DEUTZ

   Deere I agree with you .I work For a Dealer From 1981 till 1996 . I have a Tractor Repair Business for over 20 years now and work on the good ol stuff and have never looked back .


Edited by Fred in Pa - 29 Mar 2024 at 6:39am
He who dies with the most toys is,
nonetheless ,still dead.
If all else fails ,Read all that is PRINTED.
Back to Top
NEVER green View Drop Down
Orange Level Access
Orange Level Access


Joined: 28 Feb 2013
Location: MN.
Points: 7505 		Post Options Post Options   Thanks (0) Thanks(0)   Quote NEVER green Quote  Post ReplyReply Direct Link To This Post Posted: 29 Mar 2024 at 9:41am
Originally posted by jdeere562 jdeere562 wrote:

I was an Allis mechanic at two different dealers, from 1975 until 1991.
It was a nightmare with Deutz. Allis had great service manuals. Deutz manuals sucked. Few words and a bunch of symbols. About like a car from the 1960's to that current crap that pops up on the dash today. Stop and read the owner's manual to see what they mean.

Cab heaters run off diesel fuel, what a joke. Cylinder heads with stretch bolts were also a pain. In 1991 I moved on to Deere, and NOT as a mechanic either!

   My friend pulls a Deutz, those head bolts are bizarre.
2-8050 1-7080 6080 D-19 modelE & A 7040   R50       
Back to Top
1963D17 View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 05 Jun 2021
Location: Alvord, Iowa
Points: 89 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 1963D17 Quote  Post ReplyReply Direct Link To This Post Posted: 29 Mar 2024 at 10:43pm
All European parts manual were defiantly subpar. New Holland had one of the easiest to read and simple parts catalogs out there. After Fiat bought New Holland the manuals got complicated. Look at a 1915 chopper catalog and then an FX chopper manual. 
Back to Top
 Post Reply Post Reply Page  <12
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.051 seconds.


Help Support the
Unofficial Allis Forum