This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Construction and other equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


G-153 parts for FP40 forklift
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
meddleshop View Drop Down
Bronze Level
Bronze Level


Joined: 26 May 2021
Location: minnesota
Points: 7 		Post Options Post Options   Thanks (0) Thanks(0)   Quote meddleshop Quote  Post ReplyReply Direct Link To This Post Topic: G-153 parts for FP40 forklift
    Posted: 26 May 2021 at 9:14am
New member here, I'm having a hard time finding gaskets for a G-153 engine. I need the exhaust gasket but would happily buy a top end set, whatever it takes to quiet this thing down! I searched the web and tried to go through my local NAPA but had no luck. Any help appreciated
Back to Top
Sponsored Links


Back to Top
jaybmiller View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 22511 		Post Options Post Options   Thanks (0) Thanks(0)   Quote jaybmiller Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2021 at 10:20am
same BUDA engine as in a Cockshutt 30 tractor.
I think Steiner's has stuff for them....

Jay
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)

Never burn your bridges, unless you can walk on water
Back to Top
meddleshop View Drop Down
Bronze Level
Bronze Level


Joined: 26 May 2021
Location: minnesota
Points: 7 		Post Options Post Options   Thanks (0) Thanks(0)   Quote meddleshop Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2021 at 2:10pm
Thanks for the reply, problem is the gaskets they show on these sets must be a cross flow head, mine has old fashioned siamese manifold with individual gaskets for each port. 
these sets that are offered show separate intake and exhaust gaskets with 4 ports each. Maybe I should just buy it and cut into pieces.......
Back to Top
meddleshop View Drop Down
Bronze Level
Bronze Level


Joined: 26 May 2021
Location: minnesota
Points: 7 		Post Options Post Options   Thanks (0) Thanks(0)   Quote meddleshop Quote  Post ReplyReply Direct Link To This Post Posted: 26 May 2021 at 2:22pm
thanks again, I just figured it out. I looked at the replacement manifold for the cockshutt and they sell the combo gasket seperately. Better picture of the gasket.
Back to Top
meddleshop View Drop Down
Bronze Level
Bronze Level


Joined: 26 May 2021
Location: minnesota
Points: 7 		Post Options Post Options   Thanks (0) Thanks(0)   Quote meddleshop Quote  Post ReplyReply Direct Link To This Post Posted: 22 Jun 2021 at 7:22pm
I got the engine fixed, the gasket I got from Steiners wasn't correct butI was able to modify it to fit my machine. The end ports on my engine are round and the gasket came with rectangular ports on the ends only. I cut the gasket into 3 pieces so I could move the ends over enough to sort of match the round ports and punched new bolt holes. worked just fine, running good now.  
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.078 seconds.


Help Support the
Unofficial Allis Forum