This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Construction and other equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


FP40-2PS fork lift advice needed

 Post Reply Post Reply
Author
Message
CNCMan View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 17 Jan 2022
Location: Shafer, MN
Points: 4
Post Options Post Options   Thanks (0) Thanks(0)   Quote CNCMan Quote  Post ReplyReply Direct Link To This Post Topic: FP40-2PS fork lift advice needed
    Posted: 17 Jan 2022 at 1:05pm
New to the forum; Glad I found it. I have a FP40-2PS Dual LP Lift truck (4K lbs.) S/N: AMA79004.
 I suspect a blown pump seal on the transmission as massive Dexron leakage through the weep hole on the bottom of torque converter housing. 
Pulled the assembly out this past weekend. Flex plate full of cracks. Reinforcement plate ok. 
I expected to be able to pull the converter off the transmission input shaft very easily, but only about 1/4" in and out movement along the shaft axis. A fair amount of converter wobble though. The truck did still move forward and rearward while peeing Dexron out.
 Do I need to fashion a puller to attach where the flex plate was to pull the converter out of the housing on the transmission side? 
Thought I would ask prior to damaging anything else.
Next step will be parts.
 Looking for a little experience to guide me.
 Thanks,
Tom B.
Back to Top
Sponsored Links


Back to Top
jaybmiller View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 22511
Post Options Post Options   Thanks (0) Thanks(0)   Quote jaybmiller Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jan 2022 at 2:35pm
try www.liberatedmanuals.com search for 'allis forklift' , yeah you'll get 100 or so hits,read them over, download a few, just don't get 'lost' looking at all the NEAT stuff !
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)

Never burn your bridges, unless you can walk on water
Back to Top
CNCMan View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 17 Jan 2022
Location: Shafer, MN
Points: 4
Post Options Post Options   Thanks (0) Thanks(0)   Quote CNCMan Quote  Post ReplyReply Direct Link To This Post Posted: 17 Jan 2022 at 3:32pm
Yes I did spend sometime earlier looking at that connection; I found best luck using FP40-2PS and found (#1158) which seemed closest to my fork truck- perhaps a little older TM, but a good starting point.
I have only tried pulling the torque Converter off in the horizontal direction. I will try standing the entire transmission on end (setting on the U-Joint drive face) and pulling up vertically. Thought here is that if the wobble the converter has caused a groove wear on a shaft diameter going into the pump and transmission (a stator hanging up or?), perhaps a rotational shake and rattle will help me slide out the converter off the transmission shaft.
Thanks.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.078 seconds.


Help Support the
Unofficial Allis Forum