This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


8000 series fuel tank repair?
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
PeteMN View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 12 Sep 2009
Location: Hutchinson, MN
Points: 196 		Post Options Post Options   Thanks (0) Thanks(0)   Quote PeteMN Quote  Post ReplyReply Direct Link To This Post Topic: 8000 series fuel tank repair?
    Posted: 25 Jun 2024 at 10:47pm
Right hand fuel tank on our 8010 sprung a leak during planting.  I drained the remaining fuel and plugged the hose that connects it to the main tank.  Agco dealers used to have a repair kit, was wondering if anyone had ever used it to repair a small leak?
Back to Top
Sponsored Links


Back to Top
Unit3 View Drop Down
Orange Level
Orange Level
Avatar

Joined: 17 Oct 2009
Location: NC Iowa
Points: 5537 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Unit3 Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jun 2024 at 12:40am
I just went through the same thing on our 8050. The later 8000s had a used “U” shape iron that ran down the side of the tank. This holds the tank wall straight up and down instead of letting it bulge out towards the tire. I spaced my tire out one hole.

I found a two-piece putty at our local hardware store. I clean the outside of the tank as best I could and buffed it up a little with sandpaper. You work this putty in your hand until the inside putty mixes with the outside putty. I applied half of it over the whole. And then embedded some plastic screen that I have. Then I put the other half of this putty mixture over the top of the screen. I let it sit for a few days before putting fuel back in it. So far, it’s holding. Best of luck.

Edited by Unit3 - 26 Jun 2024 at 12:41am
2-8070FWA PS/8050PS/7080/7045PS/200/D15-II/2-WD45/WD/3-WC/UC/C
Back to Top
1955CA View Drop Down
Orange Level
Orange Level
Avatar

Joined: 10 Sep 2018
Location: Ontario, Canada
Points: 585 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 1955CA Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jun 2024 at 8:20am
I just had the tank off my CA while replacing the water pump and doing a valve set and when I went to put it back on discovered I now had a hole where it sits on one of the mounting pads after disturbing it. I used Permatex Cold Weld epoxy (just another version of JB Weld) No more leak.

I've also successfully used it on aluminum fuel tanks on my big rig.


Edited by 1955CA - 26 Jun 2024 at 8:21am
Back to Top
bigal121892 View Drop Down
Orange Level
Orange Level


Joined: 05 Jan 2010
Location: Nebraska
Points: 803 		Post Options Post Options   Thanks (0) Thanks(0)   Quote bigal121892 Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jun 2024 at 7:21pm
Originally posted by PeteMN PeteMN wrote:

Right hand fuel tank on our 8010 sprung a leak during planting.  I drained the remaining fuel and plugged the hose that connects it to the main tank.  Agco dealers used to have a repair kit, was wondering if anyone had ever used it to repair a small leak?

I have successfully used it to repair leaks in 8000 series fuel tank. Followed the instructions, and have never had a failure.
Back to Top
Ron(AB) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 27 Dec 2009
Location: Alberta
Points: 958 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Ron(AB) Quote  Post ReplyReply Direct Link To This Post Posted: 27 Jun 2024 at 12:28am
We had one fixed with a plastic welder.
405, 7000, 7050, 8050, 8070, L3, 2300 & 2600 disk
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum