| Author |
 Topic Search  Topic Options
|
Hardwater000 
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Allis b Ross steering box
Posted: 25 Oct 2024 at 6:11am |
|
Can someone please tell me if the pin that rides inside the worm gear is round or oblong? I have looked at various pictures and it appears to be round and somewhat coned down. I need to build mine up and like toget it shaped right the first try.if anyone has any measurements that would be great to...Tia
|
 |
|
Sponsored Links
|
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81309
|
Post Options
Thanks(0)
Quote Reply
Posted: 25 Oct 2024 at 2:19pm |
saw this on the internet several years ago.. I made a couple useing these numbers.
|
|
Like them all, but love the "B"s.
|
|
Hardwater000
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
Post Options
Thanks(0)
Quote Reply
Posted: 25 Oct 2024 at 2:31pm |
|
That helps a lot thank you.
|
|
Mikez
Orange Level Access
Joined: 16 Jan 2013
Location: Usa
Points: 8394
|
Post Options
Thanks(0)
Quote Reply
Posted: 25 Oct 2024 at 10:26pm |
|
Do have part number
|
|
JoeM(GA)
Orange Level
Joined: 12 Sep 2009
Location: Cumming,GA
Points: 4658
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Oct 2024 at 6:07am |
|
Mike, I don’t think Allis ever sold just the pin, parts book only shows the lever the pin is in, Deere did sell the pin alone, Allis chose not to.
Edited by JoeM(GA) - 26 Oct 2024 at 6:08am
|
|
Allis Express North Georgia
41 WC,48 UC Cane,7-G's,
Ford 345C TLB
|
|
Mikez
Orange Level Access
Joined: 16 Jan 2013
Location: Usa
Points: 8394
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Oct 2024 at 7:15am |
|
Yes sorry that’s what I meant. We have some nos shafts
|
|
Hardwater000
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Oct 2024 at 11:38am |
|
My pin does not appear to drive out. I used a punch but no outline of the pin on backside of shaft. Numerous post I have studied on says they drive out. And another question I have 20 ball bearings but looks like it could easily hold at least 1 more any info much appreciated
|
|
Hardwater000
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Oct 2024 at 12:27pm |
|
Nos shafts is that your personal collection or for sale?
|
|
JoeM(GA)
Orange Level
Joined: 12 Sep 2009
Location: Cumming,GA
Points: 4658
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Oct 2024 at 1:56pm |
 If you just touch the back of the arm where the pin is with a flap disc, you’ll see the outline of the pin, it’s in there good! Parts book calls for 20 balls for B & IB, 24 for C
Edited by JoeM(GA) - 26 Oct 2024 at 1:58pm
|
|
Allis Express North Georgia
41 WC,48 UC Cane,7-G's,
Ford 345C TLB
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81309
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Oct 2024 at 2:49pm |
no way the pin could be MADE on the end of the shaft. It has been pressed in... I have had to center punch and drill one out before that was TOO TIGHT..... also possible that someone instalaled a new pin and welded the back side, then ground it flush so it looks like one piece ?
YES-- 20 balls as shown in the drawing.. you want some clearance for them to roll and carry oil / grease.. Very low speed application.
|
|
Like them all, but love the "B"s.
|
|
Hardwater000
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Oct 2024 at 3:43pm |
|
May of been welded haven't gave up yet. On the bearings I will recount again but it appears that I had plenty of room for 1 maybe 2 but they do need room for oil and grease like said above
|
|
Kiwi
Silver Level
Joined: 23 Jan 2018
Location: New zealand
Points: 383
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Oct 2024 at 4:06am |
|
Hi I knocked my pin out turn it 90 degrees and put it back in so it now runs on the unworn face.
|
|
Tractors Allis EB,two C,diesel G
|
|
Hardwater000
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Oct 2024 at 5:40am |
|
I read on another topic while searching that someone did that, but mine is wore bad enough that it has to be reworked or try to buy a new one probably will rework considering the prices I have seen on new pins.
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81309
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Oct 2024 at 7:57am |
|
the first couple i did, i welded up the pin , in place, and ground it back to a cone shape with a hand grinder... At that time i didnt know the pins came out and you could buy new... AFter the first couple, i drill out the old and made new pin on the lathe out of a grade 8 bolt.
|
|
Like them all, but love the "B"s.
|
|
Hardwater000
Bronze Level
Joined: 13 Jan 2024
Location: Missouri
Points: 46
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Oct 2024 at 9:20am |
|
That is a good idea with the bolt. I maybe able to turn it down locking it into a drill press bc I don't have a lathe. Much easier I think than welding what little of the pin is left. I believe maybe it has been welded from backside and ground down I ran a flap disk over it and it's the only thing I can think of why I can't see the outline of the pin.
|
|
Mikez
Orange Level Access
Joined: 16 Jan 2013
Location: Usa
Points: 8394
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Oct 2024 at 9:57am |
|
Do you know part number of shaft
|
|
JoeM(GA)
Orange Level
Joined: 12 Sep 2009
Location: Cumming,GA
Points: 4658
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Oct 2024 at 10:59am |
|
70211001
LEVERSHAFT (TR. B-101 & UP) (B & IB)
|
|
Allis Express North Georgia
41 WC,48 UC Cane,7-G's,
Ford 345C TLB
|
|
Mikez
Orange Level Access
Joined: 16 Jan 2013
Location: Usa
Points: 8394
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Nov 2024 at 12:20pm |
|
Thanks Joe. I’ll check that number
|
|
