This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Other Topics > Pulling Forum
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Exhaust rule question
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
7060 View Drop Down
Orange Level
Orange Level
Avatar

Joined: 16 Sep 2009
Location: Missouri
Points: 1148 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 7060 Quote  Post ReplyReply Direct Link To This Post Topic: Exhaust rule question
    Posted: 26 Aug 2012 at 1:20pm
  This may be a dumb question to some of you, but I can't figure it out. I was reading the rules to an organization and all the diesel classes have this rule. Could someone explain it?

Exhaust will have 2- 5/16" bolts as close to the elbow as possible at a 90 degree angle from each other and no more than two inches apart.

Back to Top
Sponsored Links


Back to Top
DougG View Drop Down
Orange Level
Orange Level


Joined: 20 Sep 2009
Location: Mo
Points: 8110 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DougG Quote  Post ReplyReply Direct Link To This Post Posted: 26 Aug 2012 at 1:50pm
The bolts are to stop or slow down turbo parts if one should fly apart, without causeing an exhaust block of too much
Back to Top
cwhit View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Sigel IL
Points: 982 		Post Options Post Options   Thanks (0) Thanks(0)   Quote cwhit Quote  Post ReplyReply Direct Link To This Post Posted: 26 Aug 2012 at 4:49pm
Around here they also have a no curved stack rule. Should anything fly out, it will go up and not out into the spectators, for about the same reasons.
Back to Top
ACFarmer View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 13 Sep 2009
Location: Ohio
Points: 742 		Post Options Post Options   Thanks (0) Thanks(0)   Quote ACFarmer Quote  Post ReplyReply Direct Link To This Post Posted: 27 Aug 2012 at 12:45pm
Correct, they are there to stop the exhaust wheel from coming out of the stack. I have the elbow off our D-21 where the exhaust wheel came apart. Went straight back and chewed straight through the elbow and bounced about the engine compartment.
Making A living everyday farming with and working on Allis Equipment
Back to Top
7060 View Drop Down
Orange Level
Orange Level
Avatar

Joined: 16 Sep 2009
Location: Missouri
Points: 1148 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 7060 Quote  Post ReplyReply Direct Link To This Post Posted: 27 Aug 2012 at 12:55pm
So they bolt all the way through the exhaust and form an X inside?
Back to Top
allis180 View Drop Down
Bronze Level
Bronze Level


Joined: 03 Jan 2012
Location: Iowa
Points: 29 		Post Options Post Options   Thanks (0) Thanks(0)   Quote allis180 Quote  Post ReplyReply Direct Link To This Post Posted: 27 Aug 2012 at 1:16pm
Exactly.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.133 seconds.


Help Support the
Unofficial Allis Forum