This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


D14 intermediate shaft bearing advise
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
ryanschott View Drop Down
Orange Level
Orange Level
Avatar

Joined: 10 Apr 2010
Location: michigan
Points: 605 		Post Options Post Options   Thanks (0) Thanks(0)   Quote ryanschott Quote  Post ReplyReply Direct Link To This Post Topic: D14 intermediate shaft bearing advise
    Posted: 20 Oct 2024 at 8:57pm
The bearings in both intermediate shafts in the torque tube behind the power director are really worn out they rattle around I’ve taken the the tractor in half to get to them what is the easiest way to take it apart I see the center of the shafts are threaded. Just a little advise if you’ve replaced them before
Back to Top
Sponsored Links


Back to Top
Lynn Marshall View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 13 Sep 2009
Location: Dana, Iowa
Points: 2284 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Lynn Marshall Quote  Post ReplyReply Direct Link To This Post Posted: 20 Oct 2024 at 9:56pm
You need to remove the snap rings that retain the rear bearing cups and then use a slide hammer with the correct, threaded adapter. You really need a quality service manual for this job. There's a certain sequence for taking these things apart and then getting the bearings set properly. Variable thickness snap rings are what sets the bearing end play.
Back to Top
D171958 View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 03 Aug 2024
Location: Iowa
Points: 24 		Post Options Post Options   Thanks (0) Thanks(0)   Quote D171958 Quote  Post ReplyReply Direct Link To This Post Posted: 22 Oct 2024 at 7:27am
You should have to take the front pto shaft out first to remove the shafts take the snap ring off and then you get long bolt cut the head off and thread it into the shaft and a slide hammer when I did mine the tractor had been sitting a few years so I got a metal tube to fit over the shaft and put washers on the top with a nut and just kept threading it down.
Back to Top
ryanschott View Drop Down
Orange Level
Orange Level
Avatar

Joined: 10 Apr 2010
Location: michigan
Points: 605 		Post Options Post Options   Thanks (0) Thanks(0)   Quote ryanschott Quote  Post ReplyReply Direct Link To This Post Posted: 23 Oct 2024 at 10:10am
lol lot bigger job then I thought but have it broke in half and the hydro pump oil just have to get the lower pto shaft out then can take out the two I need to fix. A lot of stuff but not as bad as I was imagining
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 20534 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 23 Oct 2024 at 10:49am
When you can't get the 3 front bearing cups out of the housing stop back here and I'll explain how i get them out.
Back to Top
ryanschott View Drop Down
Orange Level
Orange Level
Avatar

Joined: 10 Apr 2010
Location: michigan
Points: 605 		Post Options Post Options   Thanks (0) Thanks(0)   Quote ryanschott Quote  Post ReplyReply Direct Link To This Post Posted: 26 Oct 2024 at 3:16pm
Got everything apart used a carriage bolt a socked and nut and plate to remove the from bearing cups. Installing the shaft into the front bearings after the gears in the way looks fun though.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum