Gleaner E engines for sale

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   I have 3 Gleaner E engines to sell. 

Engine 1.

Gleaner E take out engine on skid.  Turns over, complete MINUS manifold.  Carb, distributer etc is all there.  Missing a manifold, I bet it would run with a carb cleaning and manifold installed.  $500
 SOLD

Engine 2.

Gleaner E short block assembly.  I bought new sleeves and installed some M&W 4 1/8 bore pistons, new rings, bearings, etc.  I machined the pistons to about .010" pop up from block for a quench engine, cut valve reliefs, machined piston bowls for a 11.25:1 compression ratio.  Degreed stock cam in to 105* ATDC intake centerline.  Balanced rotateing assembly.  I had it in a WD45 and pulled it a bit.  The tractor front pulley and timeing cover are on it. 

Sold as a complete short block assembly, no governer housing or ignition, water pump, flywheel, head, manifold and related parts.  $700.

I would also consider selling the piston, sleeves, rings, and the rods from this engine as they are a sized and balanced set for someone to install in their own engine.

I do have core engine parts around to try and come up with a complete engine for a minimal additional cost.  I however do not wish to assemble, do any head work, manifold, carb work etc.  Just to busy with other projects and I need to go through things and make sure I have enough for complete engines for a couple that I am building before I let things go.  

Engine 3

Disassembled Gleaner E engine, no pistons or sleeves (locked up and junk).  Block blasted clean, good crank, all core parts, minus manifold and governer.  I have tractor front cover, crank pulley, etc to install in your tractor.  Good starter core engine for a build and you don't have to question what you are getting or going through the work buying a locked up or salvage engine.  $300
SOLD 

I've got distributers, and mag drive ignitions but I don't have any more governer housings, flywheels or water pumps on hand. 

I'd do my best to find a ride for them, help to meet up or arrange shipping.

Marty

715-790-1869

Edited by wi50 - 29 Sep 2013 at 7:48pm

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
wi50 Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Joined: 24 Sep 2010 Location: weegieland Points: 1010	Post Options Post Reply Quote wi50 Report Post Thanks(0) Quote Reply Topic: Gleaner E engines for sale Posted: 27 Sep 2013 at 3:00pm
	I have 3 Gleaner E engines to sell. Engine 1. Gleaner E take out engine on skid. Turns over, complete MINUS manifold. Carb, distributer etc is all there. Missing a manifold, I bet it would run with a carb cleaning and manifold installed. $500 SOLD Engine 2. Gleaner E short block assembly. I bought new sleeves and installed some M&W 4 1/8 bore pistons, new rings, bearings, etc. I machined the pistons to about .010" pop up from block for a quench engine, cut valve reliefs, machined piston bowls for a 11.25:1 compression ratio. Degreed stock cam in to 105* ATDC intake centerline. Balanced rotateing assembly. I had it in a WD45 and pulled it a bit. The tractor front pulley and timeing cover are on it. Sold as a complete short block assembly, no governer housing or ignition, water pump, flywheel, head, manifold and related parts. $700. I would also consider selling the piston, sleeves, rings, and the rods from this engine as they are a sized and balanced set for someone to install in their own engine. I do have core engine parts around to try and come up with a complete engine for a minimal additional cost. I however do not wish to assemble, do any head work, manifold, carb work etc. Just to busy with other projects and I need to go through things and make sure I have enough for complete engines for a couple that I am building before I let things go. Engine 3 Disassembled Gleaner E engine, no pistons or sleeves (locked up and junk). Block blasted clean, good crank, all core parts, minus manifold and governer. I have tractor front cover, crank pulley, etc to install in your tractor. Good starter core engine for a build and you don't have to question what you are getting or going through the work buying a locked up or salvage engine. $300 SOLD I've got distributers, and mag drive ignitions but I don't have any more governer housings, flywheels or water pumps on hand. I'd do my best to find a ride for them, help to meet up or arrange shipping. Marty 715-790-1869 Edited by wi50 - 29 Sep 2013 at 7:48pm
	"see what happens when you have no practical experience doing something...... you end up playing with calculators and looking stupid on the internet"

Sponsored Links