This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Other Topics > Pulling Forum
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Milling CA head
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
IBWD MIke View Drop Down
Orange Level
Orange Level
Avatar

Joined: 08 Apr 2012
Location: Newton Ia.
Points: 3733 		Post Options Post Options   Thanks (0) Thanks(0)   Quote IBWD MIke Quote  Post ReplyReply Direct Link To This Post Topic: Milling CA head
    Posted: 19 May 2020 at 1:47pm
I've got a 125 out of a CA I'm working on. Would like to bump the compression a bit. how much can you safely mill off the head? This isn't going to be an all out puller, just want it to be a bit stronger.
Back to Top
Sponsored Links


Back to Top
steve(ill) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: illinois
Points: 81254 		Post Options Post Options   Thanks (0) Thanks(0)   Quote steve(ill) Quote  Post ReplyReply Direct Link To This Post Posted: 19 May 2020 at 3:58pm
Dick L had a post a few years ago where he took off about .100 inch ... maybe he will see this post and fill in some info.
Like them all, but love the "B"s.
Back to Top
CTuckerNWIL View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: NW Illinois
Points: 22823 		Post Options Post Options   Thanks (0) Thanks(0)   Quote CTuckerNWIL Quote  Post ReplyReply Direct Link To This Post Posted: 19 May 2020 at 5:06pm
A post on yesterdays tractors, Dick mentioned milling one down  .200 , but that left the water jacket a little close.
 Here is a post where he mentions taking .150 off.

https://www.allischalmers.com/FORUM/b-engine-cylinder-head-performance_topic124536_page1.html



Edited by CTuckerNWIL - 19 May 2020 at 5:07pm
http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF
Back to Top
PaulB View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 4742 		Post Options Post Options   Thanks (0) Thanks(0)   Quote PaulB Quote  Post ReplyReply Direct Link To This Post Posted: 19 May 2020 at 8:00pm
Years ago, I sawed one up to find out the answer to that question. You can take as much as you want until the spark plug holes get weak. Instead of milling the head, I now add a dome to the piston. I make and install these myself. 
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
Back to Top
IBWD MIke View Drop Down
Orange Level
Orange Level
Avatar

Joined: 08 Apr 2012
Location: Newton Ia.
Points: 3733 		Post Options Post Options   Thanks (0) Thanks(0)   Quote IBWD MIke Quote  Post ReplyReply Direct Link To This Post Posted: 20 May 2020 at 9:01am
Thanks for the replies guys. I'll talk to the machinist as well, looks like an eighth of an inch should be doable and would bump the compression a fair bit.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum