This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Other Topics > Pulling Forum
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Allis 7000 Differential
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
KevinON View Drop Down
Orange Level
Orange Level


Joined: 07 Dec 2009
Location: Schomberg, ON
Points: 789 		Post Options Post Options   Thanks (0) Thanks(0)   Quote KevinON Quote  Post ReplyReply Direct Link To This Post Topic: Allis 7000 Differential
    Posted: 20 Nov 2024 at 8:49am
Was just wondering if there was a difference between the maroon belly 7000 differential and the black belly differential.  Looking to get one to stuff in a 185 rear.  Thanks!!
Back to Top
Sponsored Links


Back to Top
tbran View Drop Down
Orange Level
Orange Level


Joined: 14 Sep 2009
Location: Paris Tn
Points: 3297 		Post Options Post Options   Thanks (0) Thanks(0)   Quote tbran Quote  Post ReplyReply Direct Link To This Post Posted: 20 Nov 2024 at 5:10pm
200,7000 early and late all had an assy 70253512.... but a lot of difference from a 185..
When told "it's not the money,it's the principle", remember, it's always the money..
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 20523 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 20 Nov 2024 at 5:40pm
The RH bearing and cup are larger. Don't know if the RH bearing carrier could stand that much material being removed.  We've always run the stock 2-pinion with needles on the pin and in later years went to flat needle bearings behind the side gears for thrust. We run 6700 lbs in a gear 20% faster than road gear with 24.5 x 32's , twin turbos at 1200+ HP. I wouldn't think about a 4-pinion for what we have and you'll still have to needle the 4-pinion.
Back to Top
KevinON View Drop Down
Orange Level
Orange Level


Joined: 07 Dec 2009
Location: Schomberg, ON
Points: 789 		Post Options Post Options   Thanks (0) Thanks(0)   Quote KevinON Quote  Post ReplyReply Direct Link To This Post Posted: 20 hours 13 minutes ago at 9:21am
This tractor will be a 362cu in alky.  We run 7000lbs here.  I have no idea on what HP I will be running, but I would think it would be around 1000, give or take.  I appreciate the advice.  Might be just as far ahead needling the two pinion that is in it.  I had heard of people stuffing a four pinion in them, that's all.
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 20523 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 15 hours 40 minutes ago at 1:54pm
Whichever way you go, be sure to mark your transmission dipstick to carry the oil level at least 1 inch higher than it is marked for. And use 821XL or equivalent oil.

Edited by DrAllis - 15 hours 39 minutes ago at 1:55pm
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.051 seconds.


Help Support the
Unofficial Allis Forum