This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Can’t get set screw out on new D17 bendix
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
bglancy28 View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 16 Mar 2024
Location: Indiana
Points: 7 		Post Options Post Options   Thanks (0) Thanks(0)   Quote bglancy28 Quote  Post ReplyReply Direct Link To This Post Topic: Can’t get set screw out on new D17 bendix
    Posted: 26 Mar 2024 at 4:48pm
Can’t figure out how to get this set screw out of my new starter bendix. It’s different than the old style as the spring is covered and doesn’t leave enough clearance for the set screw to come in or out. The link is the new part I got.
https://www.tractorpartsasap.com/starter-drive-prestolite-style-new-d2012-113968.html?gad_source=1&gclid=CjwKCAjw5ImwBhBtEiwAFHDZxwLwl3a5hrBrmqWJHErYv-Ze60KNPlfX01vTx7LHyr825xwNVrSnQRoCLXYQAvD_BwE
Back to Top
Sponsored Links


Back to Top
560Dennis View Drop Down
Bronze Level
Bronze Level


Joined: 30 Apr 2011
Location: NE OHIO
Points: 116 		Post Options Post Options   Thanks (0) Thanks(0)   Quote 560Dennis Quote  Post ReplyReply Direct Link To This Post Posted: 26 Mar 2024 at 5:39pm
compress spring inside far enough to use a bondus ball hex wrench to back it out . 
Back to Top
bglancy28 View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 16 Mar 2024
Location: Indiana
Points: 7 		Post Options Post Options   Thanks (0) Thanks(0)   Quote bglancy28 Quote  Post ReplyReply Direct Link To This Post Posted: 26 Mar 2024 at 5:40pm
I can’t figure out how to post a picture on here but it’s not an Allen set screw it’s a flathead. Also that’s the problem I can’t get it to compress far enough to clear the outside of the set screw.
Back to Top
IBWD MIke View Drop Down
Orange Level
Orange Level
Avatar

Joined: 08 Apr 2012
Location: Newton Ia.
Points: 3727 		Post Options Post Options   Thanks (0) Thanks(0)   Quote IBWD MIke Quote  Post ReplyReply Direct Link To This Post Posted: 27 Mar 2024 at 8:35am
Well, been there done that! Had to take a die-grinder and cut a notch to get to the screw. What was worse, the drive was about an inch too long. Took it back and they did refund my money at least.
Back to Top
mdm1 View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: Onalaska, WI
Points: 2634 		Post Options Post Options   Thanks (0) Thanks(0)   Quote mdm1 Quote  Post ReplyReply Direct Link To This Post Posted: 27 Mar 2024 at 10:14am
I got this from FB. I believe it was your post. Hope it helps.
Everything is impossible until someone does it! WD45-trip loader 1947 c w/woods belly mower, 1939 B, #3 sickle mower 1944 B, 2 1948 G's. Misc other equipment that my wife calls JUNK!
Back to Top
john2189 View Drop Down
Silver Level
Silver Level


Joined: 11 Sep 2009
Location: Minerva,Ohio
Points: 304 		Post Options Post Options   Thanks (0) Thanks(0)   Quote john2189 Quote  Post ReplyReply Direct Link To This Post Posted: 27 Mar 2024 at 3:12pm
Originally posted by mdm1 mdm1 wrote:

I got this from FB. I believe it was your post. Hope it helps.


That kind of drive was on our old cat lift trucks. I would put it in a vise and compress it enough to let it go past that collar then put it on the shaft and then tighten it up then remove from vise

Edited by john2189 - 27 Mar 2024 at 3:13pm
'41 Allis B
'45 Allis B
'49 Farmall Cub
'72 IH Cub
Back to Top
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3536 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Posted: 27 Mar 2024 at 9:27pm
if its about an 1 inch to long did you get it racheted out ? it  will neeed to be spun to get it where it belongs then it wont be hard to do
Back to Top
IBWD MIke View Drop Down
Orange Level
Orange Level
Avatar

Joined: 08 Apr 2012
Location: Newton Ia.
Points: 3727 		Post Options Post Options   Thanks (0) Thanks(0)   Quote IBWD MIke Quote  Post ReplyReply Direct Link To This Post Posted: 28 Mar 2024 at 7:46am
Originally posted by HudCo HudCo wrote:

if its about an 1 inch to long did you get it racheted out ? it  will neeed to be spun to get it where it belongs then it wont be hard to do
I took mine back to all states ag parts, that's where I got it. Frustrating experience!
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.078 seconds.


Help Support the
Unofficial Allis Forum