This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Construction and other equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


hd4 torqe convertor Gauge
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
blackbirdstud View Drop Down
Bronze Level
Bronze Level


Joined: 15 Jul 2013
Location: Keene NH
Points: 17 		Post Options Post Options   Thanks (0) Thanks(0)   Quote blackbirdstud Quote  Post ReplyReply Direct Link To This Post Topic: hd4 torqe convertor Gauge
    Posted: 07 Aug 2013 at 7:02pm
I have a HD4 dozer, the gauge itself, the paper backing inside the gauge has gonwe bad and its sealed so I fugured I would pull the dash and replace it. but the thermal wire that leads to the torqe convertor line is crimped to the back of the  gaude.. so I traced it back to the line and it looks liek either a half inch or 3/4 fitting into the line. So my question  is if I buy another TEMP gauge will it have those fitting or wil I have to cut my line and crimp it to another gauge soem how??
Back to Top
Sponsored Links


Back to Top
doctorcorey View Drop Down
Orange Level
Orange Level
Avatar

Joined: 17 Jul 2011
Location: S. KC Missouri
Points: 589 		Post Options Post Options   Thanks (0) Thanks(0)   Quote doctorcorey Quote  Post ReplyReply Direct Link To This Post Posted: 07 Aug 2013 at 9:31pm
  Not sure but a replacement gauge should fit, possibly with just a pipe bushing to adapt. You can't cut the bourdon tube to the gauge, if that's what you were planning. I assume you are talking about the temp gauge.
Back to Top
doctorcorey View Drop Down
Orange Level
Orange Level
Avatar

Joined: 17 Jul 2011
Location: S. KC Missouri
Points: 589 		Post Options Post Options   Thanks (0) Thanks(0)   Quote doctorcorey Quote  Post ReplyReply Direct Link To This Post Posted: 07 Aug 2013 at 9:32pm
Originally posted by doctorcorey doctorcorey wrote:

  Not sure but a replacement gauge should fit, possibly with just a pipe bushing to adapt. You can't cut the bourdon tube to the gauge, if that's what you were planning. I assume you are talking about the temp gauge.
Add to that, I think most automotive temp gauges have a 1/2 NTP fitting
Back to Top
Coke-in-MN View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 12 Sep 2009
Location: Afton MN
Points: 41572 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Coke-in-MN Quote  Post ReplyReply Direct Link To This Post Posted: 08 Aug 2013 at 1:16pm
The gauge is a full unit, from the bulb at the end to the gauge itself . It all needs to be replaced as a unit - sensing bulb and gage itself.
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum