![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Shaver HD8 S |
Post Reply ![]() |
Author | |
DMiller ![]() Orange Level Access ![]() Joined: 14 Sep 2009 Location: Hermann, Mo Points: 30491 |
![]() ![]() ![]() ![]() ![]() Posted: 12 Dec 2022 at 2:26pm |
Wondering if anyone has added one to their Tractor as I have? Trying to come up with a way to discharge back into the Hyd Section of Torque tube besides the Dip Stick Hole/Vent. May have to drill a side plate and add a fitting, is one Boss on Right Side of torque Tube just up and left of PD access plate, APPEARS to have a drive cup plug in it wondering if that is factual where can pull it to outside and tap that hole.
|
|
![]() |
|
Sponsored Links | |
![]() |
|
exSW ![]() Orange Level ![]() Joined: 21 Jul 2017 Location: Pennsylvania Points: 914 |
![]() ![]() ![]() ![]() ![]() |
I've had one on a couple tractors. My 560D mounted on the front and my 7010 mounted on the three point. Worked better on the 7010. 1) 11000 pound tractor has a lot less bounce than a 7000 pound tractor. 2) big fat return line going straight to the sump allows that ram to drop with no resistence.
Edited by exSW - 12 Dec 2022 at 7:37pm |
|
Learning AC...slowly
|
|
![]() |
|
DMiller ![]() Orange Level Access ![]() Joined: 14 Sep 2009 Location: Hermann, Mo Points: 30491 |
![]() ![]() ![]() ![]() ![]() |
Would you consider tapping a hole in the Pulley Drive area cover to add a fitting appropriate to sump?
|
|
![]() |
|
DMiller ![]() Orange Level Access ![]() Joined: 14 Sep 2009 Location: Hermann, Mo Points: 30491 |
![]() ![]() ![]() ![]() ![]() |
Change of plans after discussion with Dr Allis
Going in dipstick port, 1" 8tpi threads. Turned this adaptor out this morning, is thru drilled 7/16" currently, will upsize a little as get a swivel fitting to fit the line off the driver. Will then drill and tap head end of adaptor then square off two sides and slot thru the threads into main body for vent path. Threads extend into housing so should be no oil blow back up too bad on threaded area. |
|
![]() |
|
exSW ![]() Orange Level ![]() Joined: 21 Jul 2017 Location: Pennsylvania Points: 914 |
![]() ![]() ![]() ![]() ![]() |
I like that!
|
|
Learning AC...slowly
|
|
![]() |
|
DMiller ![]() Orange Level Access ![]() Joined: 14 Sep 2009 Location: Hermann, Mo Points: 30491 |
![]() ![]() ![]() ![]() ![]() |
Hoping it works.
|
|
![]() |
|
DMiller ![]() Orange Level Access ![]() Joined: 14 Sep 2009 Location: Hermann, Mo Points: 30491 |
![]() ![]() ![]() ![]() ![]() |
Bought a 3/4 NPT fitting and welded it to head of Adaptor, return line is 3/4npt.
Weld not so pretty but will do just fine, made vent slit across threads so do not really over-pressure the hydraulics seals in the Torque Tube. Specs are 3/16" vent slot, 1"8 tpi adaptor thread, 1 1/4" x 3" bar stock drilled 5/8" thru and a steel 3/4" npt M-F swivel fitting. Have made and glued a gasket with Indian Head adhesive to the Adaptor face. Can screw in or out by hand, hex head on NPT fitting makes a handy wrench spot if tightens up. |
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |