	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Forum Home > Allis Chalmers > Farm Equipment

Forum Options

Create New Topic

New Posts

FAQ

Farm Equipment

New Topic

Show Topics

Page <123 4 548 >

	Topics / Topic Starter Rating	Replies	Views	Last Post
Forum Topics
	CA Valve Spring Specs By dfwallis, 21 Oct 2026 at 1:11pm	16	1216	By dfwallis 24 Oct 2026 at 3:17pm
	7000 series tie rod ends By TedN, 23 Oct 2026 at 3:39pm	4	592	By AC7060IL 24 Oct 2026 at 12:15pm
	Happy Birthday Calvin & Lars By JoeM(GA), 21 Oct 2026 at 7:07am	6	515	By Alberta Phil 24 Oct 2026 at 9:45am
	My member visit today By JW in MO, 23 Oct 2026 at 5:40pm	1	486	By rustyorange45 23 Oct 2026 at 8:11pm
	Anybody looking for a Snap coupler blade? By DiyDave, 23 Oct 2026 at 5:05pm	0	400	By DiyDave 23 Oct 2026 at 5:05pm
	D14 with a 3 point hitch By AllisD14, 21 Oct 2026 at 5:59pm	6	801	By Gary Burnett 23 Oct 2026 at 11:53am
	D17 series one early model front axle pivot pin By mdcwells, 15 Oct 2026 at 8:29pm	3	931	By Roscoe63 23 Oct 2026 at 8:41am
	D17 engine swap By Jake79, 22 Oct 2026 at 7:49pm	2	642	By DrAllis 23 Oct 2026 at 7:12am
	A&I spindles By SteveM C/IL, 21 Oct 2026 at 10:06am	7	1040	By Leon B MO 22 Oct 2026 at 8:53pm
	Brush Hog By JCSinPITTS,PA, 19 Oct 2026 at 10:58am	16	1552	By DrAllis 22 Oct 2026 at 8:22am
	7000 Series cab foam By Roscoe63, 22 Oct 2026 at 6:03am	1	411	By SteveM C/IL 22 Oct 2026 at 8:05am
	AC 170-175 Hyd pickup elbow? By Tracy Martin TN, 19 Oct 2026 at 10:36pm	5	736	By Tim NH 22 Oct 2026 at 5:20am
	Gleaner K2 corn head alignment problem By dertz19, 09 Oct 2026 at 9:42pm	6	1041	By dertz19 21 Oct 2026 at 8:36pm
	AC tool box? By Tracy Martin TN, 20 Oct 2026 at 6:02pm	2	682	By Tracy Martin TN 21 Oct 2026 at 6:56pm
	7000 black belly hydraulics By Adam Stratton, 17 Oct 2026 at 2:11pm	11	1200	By DrAllis 21 Oct 2026 at 10:04am
	3-Point Arms Stuck? By Derricks, 10 Oct 2026 at 4:27pm	25	2801	By DrAllis 21 Oct 2026 at 8:27am
	Need help connecting an 80R mower to a WD45 By JW in MO, 20 Oct 2026 at 3:15pm	3	532	By only AC orange 21 Oct 2026 at 6:41am
	7060 steering cylinder By whatscooking, 20 Oct 2026 at 6:48pm	1	429	By SteveM C/IL 20 Oct 2026 at 9:20pm
	D17 head gasket leak By Putnamd17, 20 Oct 2026 at 6:24am	9	764	By HudCo 20 Oct 2026 at 9:26am
	Will a genuine Allis coming off 170 fit a 180 By Darwin W. Kurtz, 18 Oct 2026 at 11:06pm	5	859	By DrAllis 19 Oct 2026 at 9:43pm
	Allis G quits after a minute or so, then restarts By Mike Rock, 19 Oct 2026 at 2:13pm	4	490	By JoeM(GA) 19 Oct 2026 at 8:29pm
	Dash light 7060 By whatscooking, 17 Oct 2026 at 1:21pm	3	693	By whatscooking 19 Oct 2026 at 8:24am
	190 Question By Unit3, 18 Oct 2026 at 8:37pm	1	542	By DrAllis 19 Oct 2026 at 7:22am
	7030 Block Heater By TedN, 05 Oct 2026 at 4:24am	9	1256	By TedN 18 Oct 2026 at 2:17pm
	180 questions By thendrix, 16 Oct 2026 at 9:22pm	9	1225	By thendrix 18 Oct 2026 at 2:13pm
	Simple modern tractor By Alberta Phil, 16 Oct 2026 at 10:07am	11	1464	By cjarosz 18 Oct 2026 at 11:20am
	R50/R52 Rotor drive torque hub By 977.3Ford, 08 Oct 2026 at 9:34pm	7	1211	By 977.3Ford 18 Oct 2026 at 8:54am
	8200 grain head orbital reel pros or cons By Leon B MO, 17 Oct 2026 at 8:51am	2	447	By cwhit 17 Oct 2026 at 4:41pm
	Long Manufacturing Disk Harrow Experience? By wjohn, 16 Oct 2026 at 7:32pm	2	570	By Ray54 17 Oct 2026 at 1:21pm
	L3 Gleaner? By SteveMaskey(MO), 16 Oct 2026 at 9:33pm	1	524	By Lynn Marshall 16 Oct 2026 at 10:15pm

New Topic

Page <123 4 548 >

Forum Jump

Forum Permissions View Drop Down

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Your browser does not support inline frames or is currently configured not to display inline frames.