This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Garden Tractors
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


CCKA Flywheel Won't come off
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
coggonobrien View Drop Down
Orange Level Access
Orange Level Access


Joined: 14 Nov 2010
Location: Eastern Iowa
Points: 1820 		Post Options Post Options   Thanks (0) Thanks(0)   Quote coggonobrien Quote  Post ReplyReply Direct Link To This Post Topic: CCKA Flywheel Won't come off
    Posted: 26 Feb 2016 at 7:22am
Looking for some tips on this.  Trying to pull the flywheel off to get access to the rest of the wiring harness.  Pulley is off, center bolt to crank shaft is out.  I've installed a large 3 jaw pulley onto the fly wheel with the jaws on the ring gear and the center going through where the crankshaft bolt was and it will not come off.  This is the aluminum flywheel.  I put an lp gas infared heater pointed at it for probably 40 minutes and still no luck.  any thoughts?  My dad suggest a plate bolted to the flywheel through the pulley bolts with a pusher bolt in the middle but i'm nervous i would strip the thread holes.  thanks david
Back to Top
Sponsored Links


Back to Top
jaybmiller View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 22502 		Post Options Post Options   Thanks (0) Thanks(0)   Quote jaybmiller Quote  Post ReplyReply Direct Link To This Post Posted: 26 Feb 2016 at 7:59am
David

You dad is right ! I just downloaded the Onan servica manual for the CCKA,email me at sparky.miller@cogeco.ca and I'll send the 64 page PDF to you.

Jay
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)

Never burn your bridges, unless you can walk on water
Back to Top
coggonobrien View Drop Down
Orange Level Access
Orange Level Access


Joined: 14 Nov 2010
Location: Eastern Iowa
Points: 1820 		Post Options Post Options   Thanks (0) Thanks(0)   Quote coggonobrien Quote  Post ReplyReply Direct Link To This Post Posted: 26 Feb 2016 at 8:19am
awesome thanks, I drew up a plate to have cut on the laser today that will pull it that way.
Back to Top
coggonobrien View Drop Down
Orange Level Access
Orange Level Access


Joined: 14 Nov 2010
Location: Eastern Iowa
Points: 1820 		Post Options Post Options   Thanks (0) Thanks(0)   Quote coggonobrien Quote  Post ReplyReply Direct Link To This Post Posted: 27 Feb 2016 at 11:43am
didn't get my puller burned in time but I remembered dad had a steering wheel puller and that took care of it.
Thanks
David
Back to Top
wdtom View Drop Down
Silver Level
Silver Level


Joined: 08 Dec 2015
Location: Foster, R.I.
Points: 74 		Post Options Post Options   Thanks (0) Thanks(0)   Quote wdtom Quote  Post ReplyReply Direct Link To This Post Posted: 27 Feb 2016 at 3:12pm
When you have a puller on something with tension on it it sometimes helps if you give the center screw on the puller a good smack with a hammer. Hit the end of the screw that the wrench goes on, the shock goes down the screw to the shaft and sometimes pops the shaft out of the hub. 
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.079 seconds.


Help Support the
Unofficial Allis Forum