This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Construction and other equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


fpd50 engine swap
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
jaybmiller View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 24572 		Post Options Post Options   Thanks (0) Thanks(0)   Quote jaybmiller Quote  Post ReplyReply Direct Link To This Post Topic: fpd50 engine swap
    Posted: 29 Aug 2015 at 6:26pm
Anyone KNOW if a gas Buda 6 cylinder from a Cockshutt 40 will 'drop in  replace' the Buda 4 cylinder 153 in my FPD50 series forklift?
I can get the whole tractor ,running for $2000.hate to scrap a good tractor but I just need an engine.

Dang Fall is here, soon Winter and the forklift don't like cold weather(low compression)

Jay
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)

Never burn your bridges, unless you can walk on water
Back to Top
Sponsored Links


Back to Top
JohnCO View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Niwot Colo
Points: 8992 		Post Options Post Options   Thanks (0) Thanks(0)   Quote JohnCO Quote  Post ReplyReply Direct Link To This Post Posted: 31 Aug 2015 at 12:45am
I don't KNOW, but it seems like the 6 cylinder is going to be several inches longer then the four.  Is there extra space in the engine compartment?  Would it be easier to rebuild the original engine?
"If at first you don't succeed, get a bigger hammer"
Allis Express participant
Back to Top
jaybmiller View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 24572 		Post Options Post Options   Thanks (0) Thanks(0)   Quote jaybmiller Quote  Post ReplyReply Direct Link To This Post Posted: 01 Sep 2015 at 4:52pm
Hay John, well the 6 won't fit it unless you push really,really hard though it was an option(maybe the frame is bigger ?)
I was quoted $5000 to rebuild it AFTER I deliver it to the rebuild shop.
Frankly I don't have a spare 5 thousand  to rebuild the diesel....
It needs rings( bad blowby,low power) BUT my xray eyes can't tell if it needs the 3 ring kit or the 4 ring kit, so a total sleeve/rings/piston,orings 'kit' X4 is one choice but at $400 per cyl that adds up...oh yeah 4 CDN bux buys 3 USD, and that HURTS
Now I found an nonrunning CS30 nearby but at $1500 it's a pricey gamble too...hate to scrap a nice tractor just for an engine ...
open to all ideas..
latest one...put two engines in, 16HP for drive and 16HP for hydraulics. It's possible,got the room,less than $1000 ?
sigh....
double sigh.....

Jay
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)

Never burn your bridges, unless you can walk on water
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.180 seconds.


Help Support the
Unofficial Allis Forum