| Author |
 Topic Search  Topic Options
|
AC 7060 
Bronze Level
Joined: 06 Jul 2010
Points: 144
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: 426 exhaust manifold
Posted: 08 Oct 2014 at 8:54pm |
|
Has anyone used the exhaust manifold from crank machine for a 426 on a hotfarm tractor. Dr. Said use one off a in 414 which would be better. Thanks for the help.
|
 |
|
Sponsored Links
|
|
|
O.P.S. Heads
Orange Level Access
Joined: 02 Jan 2013
Location: Iowa
Points: 574
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Oct 2014 at 9:26pm |
|
What's "crank machine"?
|
|
AC 7060
Bronze Level
Joined: 06 Jul 2010
Points: 144
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Oct 2014 at 9:56pm |
|
Crank machine service from New Baden IL they offer a new cast center feed exhaust manifold I think it is suppose to be similar to the D 21 na manifold
|
|
O.P.S. Heads
Orange Level Access
Joined: 02 Jan 2013
Location: Iowa
Points: 574
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Oct 2014 at 10:43pm |
|
as long as it is divided all the way to the turbo it will be better than any AC manifold.
|
|
AC 7060
Bronze Level
Joined: 06 Jul 2010
Points: 144
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Oct 2014 at 8:10am |
|
Will the divided manifold help if the exhaust housing doesn't have a divider in it
|
|
O.P.S. Heads
Orange Level Access
Joined: 02 Jan 2013
Location: Iowa
Points: 574
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Oct 2014 at 8:34am |
|
Yes. It would work better with a divided exhaust housing, but the exhaust pulses are better used with a divided manifold from what I understand.
Edited by O.P.S. Heads - 09 Oct 2014 at 8:35am
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20551
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Oct 2014 at 12:07pm |
|
The IH manifold has three advantages over the A-C manifold. #1. The exhaust flow only turns once coming out of the head (left or right) #2. the runners are a little smaller than the A-C keeping expansion from occurring until it hits the turbo #3. absolute pulse flow with built-in divider wall. The best IH manifold would be from a truck which would position the turbo down on the side instead of up under the hood. I haven't seen this after-market manifold, but doubt that is has more than the divider wall and flunks on #1 and #2.
|
|
cms
Bronze Level
Joined: 29 Nov 2010
Location: collinsville il
Points: 70
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Nov 2014 at 7:47am |
|
The IH manifolds don't have same bolt hole spacing and are not a true center dump.
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20551
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Nov 2014 at 5:33pm |
|
You have to make 1 inch thick spacers to adapt to the A-C head. Been there....dun that... it works better than ANY A-C exhaust manifold. The best would be the IH truck manifold.
|
|
injpumpEd
Orange Level Access
Joined: 13 Sep 2009
Location: Walnut IL
Points: 4917
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Nov 2014 at 7:11pm |
|
The one Crank Machine Service is making is a much bigger, and better looking setup for pulling. It's just whether your rules would allow since it's not oem, and couldn't pass for oem either. The cms that posted is the builder. Dan Karpel, 618-401-2386 is on a card I have.
|
|
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!
|
|
Peterson
Orange Level
Joined: 05 Mar 2011
Location: Westboro, Wi
Points: 862
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Nov 2014 at 7:17pm |
|
Will the IH manifold clear the stock oil cooler pipe on the 426?
|
|
7095-685I at 255hp, 8070-225HP,8050-210Hp,8030 with 155HP,220 with 670T engine with A-pump, 7580, 185 with 140HP, 2-6080's,6070, S4 D17,wd45,CA,st34 agco, S1 D17 with 3500MK2
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20551
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Nov 2014 at 7:35pm |
|
I did it to a D-21 and had the oil cooler removed for the in-line injection pump, so I can't really answer your question with certainty.
|
|
cms
Bronze Level
Joined: 29 Nov 2010
Location: collinsville il
Points: 70
|
Post Options
Thanks(0)
Quote Reply
Posted: 07 Nov 2014 at 9:36am |
|
The manifold I have does fit with oil cooler on.
|
|
Peterson
Orange Level
Joined: 05 Mar 2011
Location: Westboro, Wi
Points: 862
|
Post Options
Thanks(0)
Quote Reply
Posted: 07 Nov 2014 at 9:38am |
|
Some pictures would be awesome!
|
|
7095-685I at 255hp, 8070-225HP,8050-210Hp,8030 with 155HP,220 with 670T engine with A-pump, 7580, 185 with 140HP, 2-6080's,6070, S4 D17,wd45,CA,st34 agco, S1 D17 with 3500MK2
|
|
Peterson
Orange Level
Joined: 05 Mar 2011
Location: Westboro, Wi
Points: 862
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Nov 2014 at 10:36am |
|
Seen some pics of the CMS manifold and I dont see a divider in the manifold. Im not saying that its bad but it really wouldnt be any better then the stock D21,210,220 manifold. Otherwise it looks nice.
One company I'd love to have build a manifold would be "Steed Speed" look up the manifold that they build for the 5.9Cummins
Edited by peterson - 12 Nov 2014 at 11:04am
|
|
7095-685I at 255hp, 8070-225HP,8050-210Hp,8030 with 155HP,220 with 670T engine with A-pump, 7580, 185 with 140HP, 2-6080's,6070, S4 D17,wd45,CA,st34 agco, S1 D17 with 3500MK2
|
|
cms
Bronze Level
Joined: 29 Nov 2010
Location: collinsville il
Points: 70
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Nov 2014 at 11:31am |
|
The pictures are the first one out. Have dividers in all manifolds have some with out.
|
|
Peterson
Orange Level
Joined: 05 Mar 2011
Location: Westboro, Wi
Points: 862
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Nov 2014 at 11:32am |
|
How much for one with divider?
|
|
7095-685I at 255hp, 8070-225HP,8050-210Hp,8030 with 155HP,220 with 670T engine with A-pump, 7580, 185 with 140HP, 2-6080's,6070, S4 D17,wd45,CA,st34 agco, S1 D17 with 3500MK2
|
|
