| Author |
 Topic Search  Topic Options
|
bulldog 
Bronze Level
Joined: 01 May 2014
Location: UK
Points: 5
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Allis Chalmers HD5
Posted: 01 May 2014 at 11:51am |
A friend has a HD 5 with low oil pressure,all bearings have been renewed, is there a oil pressure adjustment ? what is the correct pressure, its 15 psi now Thanks Martyn
|
 |
|
Sponsored Links
|
|
|
JC-WI
Orange Level Access
Joined: 11 Sep 2009
Location: wisconsin
Points: 34278
|
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2014 at 12:15pm |
|
Was it 15 psi before the new bearings?
|
|
He who says there is no evil has already deceived himself
The truth is the truth, sugar coated or not. Trawler II says, "Remember that."
|
|
bulldog
Bronze Level
Joined: 01 May 2014
Location: UK
Points: 5
|
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2014 at 12:30pm |
|
Its alway been low , what is the correct pressure ?
|
|
bulldog
Bronze Level
Joined: 01 May 2014
Location: UK
Points: 5
|
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2014 at 12:33pm |
He has recently got the machine and had someone to work on it.15 psi seems low to me. I wondered if there was a pressure relief valve or any adjustmen to increase presure ? or perhaps the oil pump is at fault.He has no manual to work to. Thanks Martyn
|
|
Coke-in-MN
Orange Level Access
Joined: 12 Sep 2009
Location: Afton MN
Points: 41933
|
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2014 at 12:55pm |
|
new bearings will not make up for worn cam bearings or worn crank - to much clearance and low oil pressure results.
|
|
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
|
|
Matt (Jordan,MN)
Orange Level
Joined: 12 Sep 2009
Location: Jordan, MN
Points: 3799
|
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2014 at 1:11pm |
Had the same problem. We replaced the cam & balance shaft bearings and had the bearing surfaces on the shaft welded up. It fixed the problem.
|
|
Owner of Matt Scott LLC
Specializing in NOS and used Allis Chalmers tractor & implement parts & liturature and Magneto Repair
http://www.mattscottllc.com/
|
|
Coke-in-MN
Orange Level Access
Joined: 12 Sep 2009
Location: Afton MN
Points: 41933
|
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2014 at 1:56pm |
When I bought my 5G - the seller told me he had just replaced the rod and main bearings but had light oil in it and pressure was low - well I changed oil and still low so i replaced the oil pump - still low - but operable - pressure dropped at idle but would come up to 30 PSI at 1800 RPM or so . Couple years later I developed a oil leak at rear main - tore down and found crank was worn - had ground and new bearings as well as new pistons and sleeves , oil pressure came up 45 PSI . Couple years later replaced the head as one valve seat burnt and came loose . Also had small cracks to injector sleeve (a normal thing I found out later) and engine runs great yet 15 years later . Dang just counting I have owned the machine for over 35 years now - and it still runs.
Edited by Coke-in-MN - 01 May 2014 at 1:58pm
|
|
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
|
|
Coke-in-MN
Orange Level Access
Joined: 12 Sep 2009
Location: Afton MN
Points: 41933
|
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2014 at 2:03pm |
|
I have a photocopy of HD5 manual I will sell if your friend wants one
|
|
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
|
|
Ray54
Orange Level Access
Joined: 22 Nov 2009
Location: Paso Robles, Ca
Points: 4702
|
Post Options
Thanks(0)
Quote Reply
Posted: 01 May 2014 at 10:52pm |
|
Make sure it is not putting diesel in the crankcase.Detroits are known to have the fuel lines on top of the head start leaking around the fitting,but do not over tighten as that will make it leak more.They used to be cheap and just change them if there was any sign of oil being thinned with diesel.Don't know how parts are as DD as a company has had many owners in the last 20 years.And greenies don't like the 2 cycle diesel.I have seen this several times and much cheaper than new bearings.Good luck.
|
|
bulldog
Bronze Level
Joined: 01 May 2014
Location: UK
Points: 5
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 May 2014 at 11:01am |
Saw the machine today as it shared a lowboy with my D4 enroute to a vintage show, seems to run OK. Will have a closer look at the machine on Saturday. Thanks for your help.
|
|
Coke-in-MN
Orange Level Access
Joined: 12 Sep 2009
Location: Afton MN
Points: 41933
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 May 2014 at 11:59am |
|
Yes if you do any injector work or anything in that top end WATCH the injector lines . 15 inch pounds torque on line nut . double flare fitting and they will crack just behind flare thinning oil and dropping pressure .
|
|
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
|
|
chumduffy
Orange Level Access
Joined: 28 Sep 2013
Location: Smethport, PA
Points: 4951
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 May 2014 at 3:35pm |
 Coke-in-MN wrote:
I have a photocopy of HD5 manual I will sell if your friend wants one |
I would buy your manual Coke, just let me know how much you need for it and where to send you a check. Thanks', Chum..
|
|
