| Author |
 Topic Search  Topic Options
|
HudCo 
Orange Level
Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 4239
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: what model plow is this
Posted: 29 Sep 2026 at 8:48pm |
|
|
 |
|
Sponsored Links
|
|
|
HudCo
Orange Level
Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 4239
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Sep 2026 at 10:12pm |
|
4 bolts on the shears three bolts in a straight line the the front one is alittle lower none of the center to center on the bolts is the same
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 23555
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Sep 2026 at 10:24pm |
|
If the frame width can be assembled 14 or 16 inch width I'd say 70 series. Bolted only to one frame width 60 series.
|
|
HudCo
Orange Level
Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 4239
|
Post Options
Thanks(0)
Quote Reply
Posted: 30 Sep 2026 at 10:56am |
|
|
|
HudCo
Orange Level
Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 4239
|
Post Options
Thanks(0)
Quote Reply
Posted: 30 Sep 2026 at 10:59am |
|
does this help alittle bit dr. allis need to find shears for this and land slides also
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 23555
|
Post Options
Thanks(0)
Quote Reply
Posted: 30 Sep 2026 at 11:15am |
|
70-series. There is more than one plow "bottom" for the 70-series. And that determines what shares or landsides. I have made my own landsides out of 1/2" or 3/4" flat steel. They won't last as many acres as OEM, but my plow days don't happen that often and new landsides sure do keep the plow straight when plowing.
Edited by DrAllis - 30 Sep 2026 at 11:18am
|
|
jiminnd
Orange Level
Joined: 16 Sep 2009
Location: Rutland ND
Points: 2376
|
Post Options
Thanks(0)
Quote Reply
Posted: 30 Sep 2026 at 11:54am |
|
Are the shears 3 bolt or 4 bolt, that is something you need when looking for them.
|
|
1945 C, 1949 WF and WD, 1981 185, 1982 8030, unknown D14(nonrunner)
|
|
Mikez
Orange Level Access
Joined: 16 Jan 2013
Location: Usa
Points: 9026
|
Post Options
Thanks(0)
Quote Reply
Posted: 16 hours 45 minutes ago at 7:29pm |
|
Unbolt and look for part numbers on back side of any of the wear parts
|
|
IBWD MIke
Orange Level
Joined: 08 Apr 2012
Location: Newton Ia.
Points: 4433
|
Post Options
Thanks(0)
Quote Reply
Posted: 6 hours 16 minutes ago at 5:58am |
|
Had to dig the bible out and review my Allis plows. The good Dr. is right, a model 74 pull-type. Not a real common plow. If it had cushion trip bottoms it would be an 84. Dave the plowman probably has wear parts.
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 23555
|
Post Options
Thanks(0)
Quote Reply
Posted: 5 hours 42 minutes ago at 6:32am |
|
Not really a common A-C plow for sure. It would be interesting as to what tractor actually pulled it. It is set-up for a 14 inch cut, which in a mounted style would fit a D-17 in my neighborhood, but a pull type version takes more tractor to pull it. If it had been hooked to a D-19, I would have expected a 16 inch cut setting. Maybe it was pulled by a brand X tractor ???
|
|
HudCo
Orange Level
Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 4239
|
Post Options
Thanks(0)
Quote Reply
Posted: 1 hour 45 minutes ago at 10:29am |
|
i think this was a 5 bottom . some cutting has been done on the back at some time . this one was given to me. all i will use it for is plow days and parades but i will replace re build the cutting parts, just did all the wheel bearings and tires before itook it off the trailer . going to pull it with the d17d
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 23555
|
Post Options
Thanks(0)
Quote Reply
Posted: 49 minutes ago at 11:25am |
|
If it was my D-17, the drawbar would be modified and up to probably 24 inches high. Good tread 16.9 x 28 tires FULL of fluid with 12+ psi. 600 lbs of rear wheel wts (300 a side). Need 300 or 400 lbs on the nose. Let the plowing begin !!
|
|
