| Author |
 Topic Search  Topic Options
|
Pointer Hollow Farm 
Bronze Level
Joined: 28 Oct 2025
Location: PA
Points: 75
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: 8 foot disk additional weight ?
Posted: 26 Dec 2025 at 6:26pm |
On this disk someone has welded two bolts on the frame (a set on each half), I assume to add weight to the disk. I was thinking about adding some weight and I have some wheel weights. The weights I have weigh about 140#'s each. Would it be too much to add the extra 140#'s to each side or would that be too much for the bearings, etc.
I was debatiing on doing that or adding one 140# weight in the center of the disk.
Thoughts?
|
 |
|
Sponsored Links
|
|
|
AC720Man
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 5322
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Dec 2025 at 9:01pm |
|
Common addition of weight locally is a rail road tie cut to length. Haven’t seen them cause any issues.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
IBWD MIke
Orange Level
Joined: 08 Apr 2012
Location: Newton Ia.
Points: 4203
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 6:27am |
|
Probably the bigger problem you'll run into is keeping the front-end on the ground. Too much weight and picking the disc up could be a problem too.
|
|
Pointer Hollow Farm
Bronze Level
Joined: 28 Oct 2025
Location: PA
Points: 75
|
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 7:15am |
|
I just added 300 pounds in weight to the front.
|
|
Gary Burnett
Orange Level Access
Joined: 11 Sep 2009
Location: Virginia
Points: 3132
|
Post Options
Thanks(1)
Quote Reply
Posted: Yesterday at 7:34am |
|
If its not cutting enough a pull type (drawbar hitch) disc is the way to go,they will cut better and you can add all the wieght you can pull no problem.
|
|
IBWD MIke
Orange Level
Joined: 08 Apr 2012
Location: Newton Ia.
Points: 4203
|
Post Options
Thanks(0)
Quote Reply
Posted: 3 hours 35 minutes ago at 6:49am |
|
If you've got some wheel weights laying around throw them on and give it a try.
|
|
dr p
Orange Level
Joined: 24 Feb 2019
Location: new york
Points: 1459
|
Post Options
Thanks(0)
Quote Reply
Posted: 3 hours 17 minutes ago at 7:07am |
|
Gary is one of the smart guys on this site and he does bring up an important point. The snap coupler disk is more of a finishing disk than a primary tillage implement. I have one, with new blades on it, and it works great for incorporating pre emerge herbacide. But if you want to follow your moldboard plow, especially if the ground has a lot of clay or residue, you are going to be disappointed. You can take multiple passes but that just wastes fuel and increases soil compaction. Its also not great at leveling a field. If you are just doing an acre or two, you can muddle through, but any more, look for a pull type disk.
|
|
wjohn
Orange Level
Joined: 19 Jan 2010
Location: KS
Points: 2287
|
Post Options
Thanks(0)
Quote Reply
Posted: 2 hours 3 minutes ago at 8:21am |
 dr p wrote:
Gary is one of the smart guys on this site and he does bring up an important point. The snap coupler disk is more of a finishing disk than a primary tillage implement. I have one, with new blades on it, and it works great for incorporating pre emerge herbacide. But if you want to follow your moldboard plow, especially if the ground has a lot of clay or residue, you are going to be disappointed. You can take multiple passes but that just wastes fuel and increases soil compaction. Its also not great at leveling a field. If you are just doing an acre or two, you can muddle through, but any more, look for a pull type disk. |
+3 These are pretty lightweight disks. I got one with the intent of using it for fast/shallow last pass tillage to kill small weeds right before planting. I have an IH 470 disk for more severe tillage. You can certainly add as much weight to your mounted disk as your tractor can handle and keep the front end on the ground but I think you will reach that limit very quickly even with your added weights up front.
However if you have pretty sandy soil you might be okay?
|
|
1939 B, 1940 B, 1941 WC, 1951 WD, 1952 CA, 1956 WD-45
|
|
