This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Other Topics > Pulling Forum
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Bearings
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Stoges View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 27 Apr 2024
Location: Erie Pa.
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Stoges Quote  Post ReplyReply Direct Link To This Post Topic: Bearings
    Posted: 07 Dec 2024 at 4:55pm
I am replacing the pistons and sleeves in my Gleaner E due to low compression. The rod bearings were a little scored, #1 looked real good. But replacing them all..
There was a little bearing material in the sump. So I just as well clean the oil pickup, the picture is what I found. The crank moves easily, I’m afraid to pull the main.

uploads/24713/IMG_2598.jpeg
Back to Top
Sponsored Links


Back to Top
Phil48ACWC View Drop Down
Silver Level
Silver Level
Avatar

Joined: 17 Jan 2013
Location: Vermont
Points: 292 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Phil48ACWC Quote  Post ReplyReply Direct Link To This Post Posted: 08 Dec 2024 at 3:29am
I would go through that engine 100%. If you don't go through it now, you'll most likely have to do it later. 

Edited by Phil48ACWC - 08 Dec 2024 at 8:36am
Back to Top
WF owner View Drop Down
Orange Level
Orange Level


Joined: 12 May 2013
Location: Bombay NY
Points: 4691 		Post Options Post Options   Thanks (0) Thanks(0)   Quote WF owner Quote  Post ReplyReply Direct Link To This Post Posted: 08 Dec 2024 at 6:50am
Originally posted by Phil48ACWC Phil48ACWC wrote:

I would go through that engine 100%.

... at least all rod and main bearings. There has to be a reason you are getting so metal.
Back to Top
ekjdm14 View Drop Down
Silver Level
Silver Level


Joined: 20 Aug 2024
Location: Manchester UK
Points: 246 		Post Options Post Options   Thanks (0) Thanks(0)   Quote ekjdm14 Quote  Post ReplyReply Direct Link To This Post Posted: 08 Dec 2024 at 9:34am
Why be afraid? git 'er opened up and find out, with luck it'll just be off the thrust face & you can stop worrying...

Have you run a magnet over it to see if there's any iron/steel? not sure if the orange is RTV or paint. Maybe check crank end shake if you're really loathe to pull a cap. Fingers crossed it is only thrust material, I had some chunks like that (& bigger!) in my B's pan and that's what it was from.
Back to Top
Stoges View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 27 Apr 2024
Location: Erie Pa.
Points: 6 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Stoges Quote  Post ReplyReply Direct Link To This Post Posted: 08 Dec 2024 at 2:07pm
Thanks Guys, problem solved, have to pull the motor, center main spun the bearing. On the plus side hope to stop the oil leaks. Better to find it now than half way down track..
Back to Top
Phil48ACWC View Drop Down
Silver Level
Silver Level
Avatar

Joined: 17 Jan 2013
Location: Vermont
Points: 292 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Phil48ACWC Quote  Post ReplyReply Direct Link To This Post Posted: 09 Dec 2024 at 6:19am
Now is the time to do a real detailed complete engine overhaul. Do it right the first time.
Back to Top
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3606 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Posted: 09 Dec 2024 at 8:20am
that looks like the crankis coming out to be turned
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.087 seconds.


Help Support the
Unofficial Allis Forum